background image

3

ASSEMBLY

PARTS

TO ENSURE SAFE OPERATION OF YOUR STROLLER, PLEASE FOLLOW THESE

INSTRUCTIONS CAREFULLY. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE

ASSEMBLY:

* Remove stroller from box. The front wheels, rear wheels, child tray,

and parent tray need to be installed prior to use.

* Lean the stroller backwards so that it rests on the handle and rear frame

tubes and the front wheel tubes are pointing upward. Position the front

wheel assembly at the front tube such that the hole in the swivel

assembly will slide onto the front tube. Please see figure 2. Push each

front wheel assembly onto the front tube being careful that wheel

assembly locks onto the front leg. Pull on the wheel assembly to

ensure that it is securely attached to the stroller. Please see figure 2.

* Assemble the rear axle as follows: Slide each wheel onto the rear axle

and secure in place with the Locking Cap. Snap the solid cap over the

Locking Cap. Snap the Hub Cap onto the wheel. Please see figure 3a.

Please see figure 3b for order assembly. Pull on each wheel to ensure

that it is securely attached.

* Lean the stroller forward to rest on the front wheels. To attach the rear

wheels, position the rear axle and wheel assembly such that the brake

levers are facing to the rear of the stroller. Press the rear wheel

assembly onto the rear frame tubes being careful that the buttons on the

inside of each rear axle housing engages the holes on the trailing edge

of each rear frame tube. Pull on the rear wheel assembly to ensure that

it is securely attached to the stroller. Please see figure 4. Ensure that

the wheels are firmly locked into place. Do Not use the stroller if the

wheels are not locked into place, but rather contact our customer

service department immediately at (800) 328-7363, between the hours

of 8:00am and 4:30pm PCT, for assistance

Fig. 1

Fig. 2

Fig. 3a

Fig. 4

Fig. 3b

Stroller

Axle

Front Wheels

Base

Rear Wheels

Child Tray

Parent Tray

Locking

Cap

Solid

Cap

Hub

Cap

Solid Cap

Locking Cap

Hub Cap

Car Seat

Summary of Contents for Trendsport Traveler laurel oak








Reviews: