Baby Trend DOUBLE SNAP N GO 1304TW Instruction Manual Download Page 8

Page: 8 / 14

Installation Instructions for Century

Vante

The Double Snap-N-Go

will accommodate the Century

Vante Infant Car

Seat. Please follow the following instructions for proper installation of the

Vante.

Front Seat:

1. Remove (unscrew) Crossbars A1, B1, C and D from the

Double Snap-N-

frame. Retain the screws you remove.

2. Attach Crossbar C on top of Crossbar B1, with the bent side of B1 facing

downward, to the

Double Snap-N-Go

frame using the two holes labeled

#2. Use the two long screws provided separately. Please see figure 1.

3. Attach Crossbar B1, taken from the rear of the

Double Snap-N-Go

frame,

to the

Double Snap-N-Go

frame using the two holes labeled #7. Use the

two screws that you removed in step 1. Please see figure 1.

Rear Seat:

1. Remove (unscrew) Crossbars A2, B2, and B1 from the

Double Snap-N-

frame. Remove the Car Seat Straps from the

Double Snap-N-Go

frame. Retain the screws you remove.

2. Attach Crossbar D, removed in the Front Seat step 1 above, to the

Double

Snap-N-Go

frame using the two holes labeled #5. Use the two screws

that you removed in step 1. Please see figure 2.

3. Attach both Car Seat Straps to the

Double Snap-N-Go

frame using the

two holes labeled #4. Use the two screws that you removed in step 1.

Please see figure 2.

Insertion of the Century

Vante Infant Car Seat

1. With one hand grasp the car seat handle (in its upright, carrying position)

and gently place the seat, so that the baby faces the rear of the

Double

Snap-N-Go

, onto the

Double Snap-N-Go

so that the large groove on the

seat bottom, nearest the head-end of the seat, hooks over the Crossbar C/

B1 combination in the front position or hooks over the top section of the

Double Snap-N-Go

frame in the rear position. Check that the seat locked

onto the Crossbar or frame. See Figure 3.

FOR SAFE OPERATION,

IT IS VERY IMPORTANT THAT THE SEAT LOCK SECURELY

ONTO THE CROSSBAR OR FRAME.

2. Feed the Car Seat Straps through the auto belt slots on the infant car seat as

shown in Figure 4 and snap the two buckles together. The first time your

do this, you will need to adjust the length of the strap for a tight fit around

the car seat.

FOR SAFE OPERATION, IT IS VERY IMPORTANT

THAT THE CAR SEAT STRAP IS ALWAYS TIGHTLY FASTENED

OVER THE CAR SEAT.

3. Test for secure installation by moving the car seat in all directions. The

car seat should be securely attached to the

Double Snap-N-Go

Removal of the Century

Vante Infant Car Seat

1. Unlock the Car Seat Strap and remove from over the infant car seat.

2. With one hand, grasp the car seat handle (in its upright, carrying position)

and with your other hand squeeze the handle on the back of the car seat

and lift the car seat upward from the

Double Snap-N-Go

frame. See

Figure 5.

Bar C

Bar B1

Hole #7

Hole #2

Hole #6

Bar B1

Strap

Bar D

Hole #4

Hole #5

Strap

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Century

and Vante are the trademarks of their owners. They are not

associated with Baby Trend and no approval or endorsement is implied.

Summary of Contents for DOUBLE SNAP N GO 1304TW















Search results

Summary of Contents for DOUBLE SNAP N GO 1304TW

Reviews:

Brands by name

Popular brands

Baby Trend DOUBLE SNAP N GO 1304TW, Instruction Manual

Search results

Summary of Contents for DOUBLE SNAP N GO 1304TW

Reviews:

Brands by name

Popular brands