background image

TO ENSURE SAFE OPERATION OF YOUR STROLLER, PLEASE FOLLOW 

THESE INSTRUCTIONS CAREFULLY. RETAIN THESE INSTRUCTIONS FOR 

FUTURE REFERENCE.

ASSEMBLY

1.   Remove stroller from box. The front wheels, rear wheels, child tray,  and 

canopy need to be installed prior to use.

2.   To attach the front wheels, unfold stroller as described in the section 

following.  Fig. 1.  Lean the stroller backwards so that it rests on the 

handle  and  rear  frame  tubes  and  the  front  wheel  tubes  are  pointing 

upward.  Position the front wheel assembly at the front tube such that 

the large hole in the swivel assembly will slide onto the front tube.  Push 

each front wheel assembly onto the front tube being careful that wheel 

assembly locks onto the front leg.  Pull on the wheel assembly to ensure 

that it is securely attached to the stroller.  Fig. 2.

3.   Lean the stroller forward to rest on the front wheels.  To attach the rear 

wheels, position the rear axle and wheel assembly such that the brake 

levers are facing to the rear of the stroller.  Press the rear wheel assembly 

onto  the  rear  frame  tubes  being  careful  that  the  push  buttons  on  the 

forward side of each rear tube engage the hole on the forward side of 

each rear wheel housing.  Pull on the rear wheel assembly to ensure that 

it is securely attached to the stroller.  Fig. 3.

4.   Ensure  that  the  wheels  are  firmly  locked  into  place.  Do  Not  use  the 

stroller if the wheels are not locked into place, but rather contact our 

customer service department immediately at (800) 328-7363, between 

the hours of 8:00am and 4:30pm PST, for assistance.

5.   Snap  footrest  onto  front  legs  of  stroller  just  below  the  seat.    Push 

downward on the footrest until it locks onto the rivets protruding from 

both sides of each leg and snaps onto the U-shaped frame cross member.  

Fig. 4.

Snap On

Push

Down

PARTS

ASSEMBLING

Fig. 1.

Fig. 2.

Fig. 3.

Fig. 4.

Child Tray

Foot Rest

Canopy

Front Wheels

Stroller

Snap N Go Attachment

Rear Wheels

Parent Tray

3

 Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.

Summary of Contents for 7311 LX








Reviews: