Baby Relax DA6526 Assembly Manual Download Page 15

That's it ! You've finished assembling your 2 in 1 convertible crib!

2 IN 1 CRIB

DA6526

        

CAUTION:

 This unit is intended for use only with the 

products and/or maximum weights indicated. Use with other 

products and/or products heavier than the maximum weights 

indicated may result in instability or cause possible injury.

ANY MATTRESS USED IN THIS 

CRIB MUST BE AT LEAST  27-1/4 

INCHES BY 51-5/8 INCHES (69CM 

BY 131CM) WITH A MINIMUM 

THICKNESS OF 4 INCHES (10CM) 

BUT NOT EXCEEDING 6 INCHES 

(15CM).

Stop using crib when child begins 

to climb out or reaches the height 

of 35 inches (89 cm).

Maximum weight not to exceed 50 

pounds when used as a crib.

The DAY BED is not intended for 

children under 15 months of age or 

over 50 pounds (22.7 kgs).

DO NOT RETURN PRODUCT TO THE STORE.

If a part is missing or damaged, contact our customer service 

department. We will replace the part 

FREE

of charge.

Tel #: 1-800-295-1980

E-Mail: [email protected]

Fax #: 514-353-7819

NEED HELP!

CALL US FOR ASSISTANCE

1-800-295-1980

DO NOT RETURN PRODUCT TO STORE
E-MAIL:[email protected]

Summary of Contents for DA6526

















Reviews: