Baby Lock BLMY Service Manual Download Page 178

Page: 178 / 226

4 - 17

Adjustment (Main Unit)

spection and

Adjustment

Feed adjustment

1. Remove the front cover, and turn on the power while pushing SW1 and SW3 on the main PCB assy. (the buzzer

sounds four times and test mode starts)
*See (4 - 4 "Test Mode") for starting test mode with the front cover in place.

2. Press SW3 (with the front cover in place, press

five times, select

and press

), and select "Feed

forward and reverse mode."

3. Press SW1 (with the front cover in place,

) and run "Feed forward and reverse mode," checking the forward

and reverse feed amounts.

4. Loosen the FPM holder assy. screw (3 x 8).

5. Adjust the forward and reverse feed using the FPM holder assy. screw (4 x 25).

6. Tighten the screw (3 x 8).

*Key point

• Confirm that when a material of two layers of broadcloth with paper in between is given 100 stitches forward

and reverse ("Feed forward and reverse" mode), the forward side is 0 – 10 mm longer than the reverse side.

• Tightening the screw (4 x 25)

shortens the reverse side.

• Loosening the screw (4 x 25)

lengthens the reverse side.

Summary of Contents for BLMY



































































































































































































































Search results

Summary of Contents for BLMY

Reviews:

Related manuals for BLMY

Brands by name

Popular brands

Baby Lock BLMY, Service Manual

Search results

Summary of Contents for BLMY

Reviews:

Related manuals for BLMY

Brands by name

Popular brands