background image

13. TROBLESHOOTING GUIDE FOR JET-AIR THREADING

                                                                           

(EXCEPT BLE1SX)

NOTE: Before adjustment of JET-AIR THREADING SYSTEM,
            please check the following items.

1  Is the machine lock button engaged?
2  Is the looper threader selector at the appropriate setting?
         "U" position for Upper Looper
         "L" position for Lower Looper 
         "C" position for Chain Looper  (BLE8, BLE8W, BLE5) 
3  Is there at least 2cm of the thread end in the threading port?
4  Is there at least 40cm of loose thread beyond the threads guide above 
    the threading port?
5  Is there a kink or twist in the 40cm of thread to restrict the blow into threading port?
6  Did you pull out old thread from loopers completely?
7  Is there any lint or dust in the threading port ?
8  Did you depress the looper threader lever strongly?
9  Is the machine for two thread sewing? (Is the subsidiary looper set?)
10  Did you use proper (regular) thread?
      Special decorative or thick threads are not threaded by JET-AIR. 

1

A

B

C

D

2

4 5

6

7

8

9

10

3

11

Summary of Contents for BLE1























Reviews: