background image

www.babbittinternational.com 

Reference Manual 

 

2021

 

 

 

18 

 

4.3 Time Delay 

 
       The purpose of the time delay is to allow the pump to prime itself or ignore voids in the process for a          

 

        preset period of time. The time delay is adjustable between 1/8 second to 2 hours. If no time delay is      

 

        required, turn the time adjustment pot completely CCW and set S1 down, S2 up. The potentiometer has                       

 

        20  turns and freewheels at the end of its travel without damage. You may hear “clicks” at the end of  

 

        travel. 
 

 

4.3 Setting the Time Delay 
 

     1)   Setting the timing mode, either on delay or off delay, is done by positioning S3 and S4 as shown in the 

chart below. 
 

NOTE: 

S3 and S4 also select fail safe high level (FSH) or fail safe low level (FSL). 

 

     2)   Select the timing range using S1 and S2 as shown on the chart below. 
     3)   Adjust the time adjustment potentiometer clockwise to increase time or CWW to decrease until the 
             exact time delay is reached. The test switch may be depressed to start the timing when checking timing 

sequence. 
 

NOTE: 

For long timing ranges you can set the timer for a shorter range, then 

change the range switches (S1 and S2) to increase the time. For example, the desired 
time delay is 15 minutes. This is equal to 900 seconds. By setting S1 down and S2 up 
and adjusting the timer to approximately 28 seconds, the ratio on this range is 1. To 
increase this range by 32, move S1 up and S2 up. 32x28 seconds equals approximately 
15 minutes. 
 

 

4.5 Fail Safe Selection 

 
     The failsafe feature provides a “false alarm” in case of power outage or major component failures. When 

                   properly selected, the failsafe feature can protect equipment or alert you of a unit failure. Fail Safe High 
 

      (FSH) means that the relay is energized when NO PRODUCT is touching the sensing element. The green 

 

      led indicates relay status and is on when the relay is energized. When product comes into contact with the 

 

      sensing element, the relay is de-energized. Fail Safe Low (FSL) means that the relay is energized when 

 

      PRODUCT IS touching the sensing element. 

 

 
                                   
            

 

                       

                    

NOTE:

 Due to the wide variety of applications and possible control or alarm functions, the proper fail   

 

safe selection will depend on your circumstances. Please call your distributor or the factory if 

 

you need assistance. 

 

 

Summary of Contents for LS8500





















Reviews: