background image

6. WARRANTY 

All components of the LS8000/2 are warranted to be free from defects in material and workmanship for a 
period of two years from the date of purchase.  This warranty applies to general purchaser and to 
components installed, serviced and operated according to instructions. 
 
Babbitt International, Inc. will repair or replace, at its option, FOB at its plant or any other location 
designated, any part which proves to be defective in manufacture or workmanship. 
All claims must be made in writing within the warranty period.  No claims outside of the warranty period 
will be honored. 
 
Warranties are not applied to any components which have been damaged by improper installation, use, 
exposure to unusual atmospheric conditions or components which have been misused, abused, damaged 
by neglect or accident.  This warranty shall not apply to any components, which have been altered or 
repaired without the prior written consent of Babbitt International, Inc. 
 
Babbitt International, Inc. assumes no responsibility or liability for any labor or material back charges, 
without written authorization.  Any products returned must be with prior written authorization. 

 

THE FOREGOING IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, 

INCLUDING ANY WARRANTIES OF MERCHANTABILITY AND/OR FOR FITNESS FOR  
PARTICULAR PURPOSE, AND BABBITT INTERNATIONAL, INC.  ASSUMES NO OTHER  
LIABILITIES EXPRESSED OR IMPLIED.  BABBITT INTERNATIONAL, INC. SHALL NOT BE  
LIABLE FOR NORMAL WEAR AND TEAR, NOR FOR DIRECT, INCIDENTIAL OR  

CONSEQUENTIAL DAMAGES.  IN NO EVENT SHALL BABBITT INTERNATIONAL  
INCORPORATED’S LIABILITY EXCEED THE PRICE OF ITS PRODUCT AT THE TIME  
OF PURCHASE.

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

15

 

Summary of Contents for LS8000/2


















Reviews: