Version 2016-001
Page 2
For Example:
If given RUN TIME=30 min., and MIST CYCLE is set as ON, the program will water 15 min automatically and after 1 0
minutes it will water for another 15 min.
9.
Set the watering days, an icon of raindrop is blinking on the left side of MO (Monday) at the beginning. Press button B
to select the watering day of week or press button C to skip it. The raindrop will be stuck to the side of selected days of
week. Press A to save it.
If the CYCLE TIME is equal or more than 2 days, the watering day of week could not be selected. The system will show the
raindrop icon automatically on the watering day.
All values are set already, it will flash two times and start to work.
10.
To reset previous program, pressing button A until the symbol
appears and “Program ON” will flash. Set the
program ON/OFF by pressing button B or C, then press A to save it and repeat above setting step 1 to step 9.
After the program is set, LCD only shows “CURRENT TIME.” By pressing button A, “START TIME” will be shown.
Note:
Situation which setting is interrupted.
At any mode, the program will leave setting procedure and give up setting when setting action is inactive beyond 3 minutes.
In case “first time” setting, the program will start to work as the timer is set already.
In second time for further time setting, the program will give up all settings have been done and show previous setting values.
Manual ON/OFF function:
1.
VALVE ON:
Press button B to start manual watering. You can see the blinking of symbol
and RUN TIME.
Under such situation, the program will be interrupted and timer will be instructed to execute manual watering.
Built-in manual operation time is 30 minutes. You may set the manual watering time by pressing button B and button C
together until the value of RUN TIME is blinking, setting the value by button B and C then press button A to save the time.
The reading range of this model is from 0 to 199 minutes.
2.
VALVE OFF:
Press button C to stop manual watering or watering in the RUN TIME period.
Trouble – shooting guide:
1.
If the water cannot come out, please check the following:
a.
The faucet / tap should be turned ON.
b.
Make sure your battery is in good condition.
c.
Time is set to the correct time including AM/PM.
d.
Check if FREQUENCY and RUN TIME is the same as the setting record.
e.
FREQUENCY time must be “LONGER” than RUN TIME.
f.
Fast knob turning could cause some miss of program reading.
2.
During watering, the symbol
blinking, and “RUN TIME” value will count down while watering is in progress.
3.
Under the status of “Program OFF”, “START TIME” will not be shown. RUN TIME, CYCLE TIME and MIST CYCLE will show
previous setting value.
4.
In any time, press button A to check next START TIME.
5.
Programmed watering schedule will be overridden by instruction of compulsive watering (Manual ON).
6.
When programmed watering schedule is interrupted, unfinished cycle will be cancelled automatically.
Summary of Contents for Jumbo WT-078
Page 1: ...BG ITEM NO WT 078 B B C A 1 9V 2 Menu o k 1 2 On 1 2 3 C Off 1 2 3...
Page 5: ...1 0 5 bar 2 12 bar 3 40 C 104 F 1 2 3 4 5 BG 1 2 3 4 5 6 7 8 9...
Page 9: ...GR ITEM NO WT 078 B B C A 1 9V 2 Menu o k 1 2 On 1 2 3 C Off 1 2 3...
Page 13: ...1 0 5 bar 2 12 bar 3 40 C 104 F 1 2 3 4 5 1 2 3 4 5 6 7 8 9...
