manualshive.com logo in svg

B-TEK Scales Centurion-AT, Installation Manual

Share
Download
B-TEK Scales Centurion-AT Installation Manual Download Page 6

5 

 

Choosing a Site 

 

    

The first step in installing the scale is to choose an appropriate site. Pertinent steps in 
choosing the site are: 
 
 

- Ensure that the site has adequate approaching / exiting distance to comply with state 
  and local Weights and Measures regulations. Scale length and scale elevation 
  (maximum fall per foot allowance) will impact the total area requirement. 

 
The site selected must meet state and local requirements. The following is taken directly 
from Handbook 44 (H-44) issued by the National Institute of Standards and Technology. 
 
 UR.2.6. 

Approaches 

 

UR.2.6.1., Vehicle Scales - On the approach end or ends of a vehicle scale installed 
in any one location for a period of six months or more, there shall be a straight 
approach as follows: 
 
(a) The width at least the width of the platform, and 
 
(b) the length at least one-half the length of the platform but not required to be more 
      than 40 feet, and 
 
(c) not less than 10 feet of any approach adjacent to the platform shall be constructed 

of concrete or similar durable material to insure that this portion remains smooth 
and level and in the same plane as the platform.  However, rating of sufficient 
strength to withstand all loads equal to the sectional capacity of the scale may be 
installed in this portion.  Any slope in the remaining portion of the approach shall 
insure, 1) ease of vehicle access, 2) ease for testing purposes, and 3) drainage 
away from the scale. 

 
The scale drawings provided meet part (a) of this requirement. The site must be 
located to meet parts (b) and (c). 

 
The site should have adequate room for trucks to properly align with the platform before 
pulling on. This is especially important if trucks must turn before driving onto the scale. 
 
Trucks should remain on the scale for a period of time no longer than is necessary for 
obtaining the vehicle weight. Drivers / passengers / pedestrians should not exit their vehicles 
or use the scale platform as a walkway. 
 
Some jurisdictions require that the scale platform be clearly visible from the location of the 
scale instrument. Others will allow the use of closed circuit TV or even a voice intercom. 
Obtain official approval before starting construction. 

 

Summary of Contents for Centurion-AT
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands