background image

2

CONTENTS

Installation Safety Notes......................................................................................................................
Parts List....................................................................................................................................................
Typical Installation.................................................................................................................................
Installation Notes...................................................................................................................................
Installation Instructions.......................................................................................................................
Product Dimensions...........................................................................................................................
B-Tech Contact Details.......................................................................................................................

2
4
6
6
8

23
24

 

CAUTION:

Do not attempt to install this product until all instructions and warnings have been read and properly understood.

Please keep these instructions for future reference. 

Please check carefully to make sure there are no missing or defective parts - defective parts must never be used.  

B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper 

installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire. 

Check with the place of purchase for information on any guarantees, repairs or replacements of this product.

  

  

 

General

B-Tech AV Mounts recommends that a professional AV installer or other suitably qualified person install this product. 

Great care must always be taken during installation as most AV equipment is of a fragile nature, possibly heavy and

easily damaged if dropped.

If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a 

professional for advice and/or to install this product for you. Failure to mount this product correctly may cause serious 

injury or death, both during installation and at any time thereafter. 

Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing.

This weight limit will be clearly stated on each product and its packaging and will vary from product to product. 

Product location

Fixing hardware

It is highly recommended that all fixing screws be used where supplied and that the purpose of all other fixing hardware 

is fully understood. In some cases more AV equipment fixing hardware will be supplied to accommodate different models 

of equipment and set up configurations. The installer must be satisfied that any supplied fixing hardware is suitable for 

each specific installation. 

If any fixing screws or included hardware are deemed not sufficient for a safe installation then please consult a professional 

or your local hardware store.

                                              This mount is intended for use only with the 
maximum weights indicated. Use with equipment heavier than the
maximum indicated may result in instability causing possible injury.  

Hazard limitation

Operating & Maintenance

When routing cables take advantage of any built in cable management features that the product might provide and ensure 

that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling. 

Some products have moving parts and the potential to cause injury through the crushing or trapping of fingers or other 

body parts. Particular attention to the nature of moving parts is required especially when assembling installing and adjusting

during set up. Immediately after installation double-check that the work done is safe and secure. Double-check all

necessary fixings are present and are of ample tightness. 

It is recommended that periodic inspections of the product and its fixing points are made as frequently as possible (no more 

than 6 months apart) to ensure that safety is maintained. B-Tech AV Mounts recommends that a suitably qualified person is used 

for the removal of this product. Please dispose of the product and packaging carefully and with consideration to the environment. 

If in doubt consult a professional AV installer or other suitably qualified person. 

INSTALLATION & OPERATING SAFETY INSTRUCTIONS

Please pay careful attention to where this product is located. Designed for indoor use, this stand is suitable for public or 

home installation. Check load capacity of the floor prior to installation to ensure that it can support the combined weight 

of the equipment and hardware, some surfaces are not suitable for installation.  

When verifying the stability of the structure, consider the following external factors: The strength of the floor, exposure to 

sudden and severe wind and danger arising from contact with people and / or objects (eg installations in passageways, 

emergency exits), if located in a public or frequently populated area ensure that the product is out of the immediate reach

of people.  When drilling holes it is essential to avoid contact with electrical cables and water or gas pipes contained within.  

Use of a good quality live wire detector and hidden object locator is therefore recommended. Only drill into structures 

when you are sure it is safe to do so.  

Summary of Contents for BT8375

























Reviews: