background image

8

This can be done during priming, or prior to the patient being put onto the 
OMNI. Be careful not to move the machine during priming to avoid any errors.

It is important to ensure the Calcium Chloride and Citrate used adhere to the 
concentrations set on the OMNI to ensure the volumes being delivered by the 
machine are correct.

When using citrate we must not change the blood flow unless stated on the 
protocol or informed so by a Consultant. If we change our blood flow, we are 
altering the amount of citrate we are giving. Consult medical/senior nursing 
staff regarding queries over the citrate protocol.

ENTERING PARAMETERS

When entering parameters it is advisable to leave the ‘therapy time limit’ 
section as a dash, not entering anything into this box to allow the machine 
to run for the lifetime of the set. Therapy time limit does not appear on the 
Confirm Therapy Parameters page.

Enter the net fluid removal as zero or desired flow prior to start of therapy. 
Please be careful to enter net fluid removal (fluid to be removed in mls/hr) and 
the dialysate flow in the correct boxes. Ensure to follow the protocol carefully 
and check parameters that have been input to avoid any potential errors. 

THERAPY TIME LIMIT

NET FLUID REMOVAL

Summary of Contents for Omni





















Reviews: