Ayrton VersaPix-RS, User Manual

Page: 8 / 16

USER MANUAL _
8
If the screen fails to respond, hold the “Mode Esc” key down for at least 3
seconds to free up the display.
The fixture’s menu functions are described in the following table:
TABLE 1: VERSAPIX-RS MENU FUNCTIONS AND OPTIONS
Address Set Dmx Addr A001~AXXX DMX address setting
Mode
User Mode Stand Mode
Basic Mode
Extend Mode
User Mode A
User Mode B
User Mode C User’s mode to change
channel numbers
Edit User Max channel
Strobe
: Preset User modes
Options
Status No DMX Mode Close/Hold/Auto Auto run if no DMX
Service PIN Service PIN
RDM PID Password=XXX
xxxxxx Service Password”=050”
RDM PID Code
Fans Control Auto
Stage
Studio Fans Speed select
Disp.Setting Shutoff Time
Flip Display
Key Lock
DispFlash 02~60m 05m
ON/OFF
ON/OFF
ON/OFF Display shutoff time
Reverse 180 degree
Key Lock
No Signal Flash
Temp. C/F Celsius
Fahrenheit Temperature switch
between
Initial Pos. Strobe =XXX Initial effect position
Trigger DMX Value Disp.
Set To Slave
Auto Program Strobe……
Slave1,Slave2,Slave3
Master / Alone DMX value display
Slave setting
Auto program
ResetDefault ON/OFF Restore factory set.
Info
Time Info. Current Time
Ttl Life Hrs
Last Run Hrs
Timer PIN
Clr Last Run XXXX(Hours)
XXXX(Hours)
XXXX(Hours)
Password=XXX
ON/OFF
Temp. Info Head Temp. XXX °C/°F
Software Ver V1.0... Software version
Test
Test Channel Strobe …… Test function
Manual Ctrl. Strobe =XXX
: Fine adjustment of
parameters
Preset
Select Prog. Prog. Part 1 = Program 1 ~ 10 Program 1
Prog. Part 2 = Program 1 ~ 10 Program 2
Prog. Part 3 = Program 1 ~ 10 Program 3 Select programs to be run
Edit Prog. Program 1
:
Program 10 Program Test
Step 01=SCxxx
Step 64=SCxxx Testing program
Program in loop
Save and exit
Edit Scenes Edit Scene 001
~ Edit Scene 250 Pan,Tilt,……
--Fade Time--
--Secne Time--
Input By Outside Save and automatically
return
manual scenes edit
Scenes Input XX~XX Automat. scenes rec
VERSAPIX-RS CONTROL PANEL MENU – OPTION
DETAILS
The following section provides details on the options that can be selected
through the control panel menu. Refer to the table above.
Note: You can exit this menu at any time by pressing “Mode Esc” repeatedly
until you return to the home screen.
ADDRESS
SET DMX ADDR
Allows you to change a DMX address from the fixture’s control panel.
w Access the menu by pressing the “Mode Esc” key.
w Go to the “ADDRESS” menu and press “Enter”, then find “Set DMX
Address.”
w Use the up/down arrows to scroll through until you locate the desired
address and press “Enter” to confirm.
MODE
USER MODE
Allows you to select the DMX mode from the following: “Basic Mode” (6,
12, 29 DMX channels ), “Standard Mode” (12 DMX channels), “User Mode
A”, “User Mode B”, “User Mode C.”
w
Access the menu by pressing the “Mode Esc” key.
w
Use the up/down arrow keys to reach the “MODE” menu and press
“Enter.” Then from “User Mode” choose one of the 6 modes above.
Consult the “CHART DMX” table for more information on Basic and
Standard Mode. “User Modes A”, “B”, or “C” are user-definable.
EDIT USER A, B, C
To customize the mode, go to “MODE” and select “Edit UserMode A, B or
C” and press “Enter.” Scroll through each setting and press “Enter” to set
the desired address.
OPTIONS
STATUS
No DMX Mode
Defines the fixture’s state when there is no command signal from the DMX
controller. The fixture can either launch a program automatically, close the
shutter, or even remain in the state when the last DMX values (Hold) were
received. The default setting is “Hold.”
w Access the menu by pressing the “Mode Esc” key.
w Use the up/down arrow keys to reach the “OPTION” menu and press
“Enter.” Then use the left/right arrow keys to select “Status.” Finally, use
the left/right arrow keys to select “No DMX Mode.”
w Scroll through the different options using the left/right arrows and press
“Enter” to confirm.
SERVICE PIN
WARNING! For normal operation the “Service pin” menu information
should not be changed. Contact your dealer for more information.
Service PIN
Allows you to enter a password to access the advanced options such as
RDM PID (pwd: 50).
w Access the menu by pressing the “Mode Esc” key.
w Use the up/down arrow keys to reach the “OPTION” menu and press
“Enter.” Finally, use the left/right arrow keys to select “Service Pin.”
w Scroll up to “50” using the left/right arrows and press “Enter” to confirm.
RDM PID
Allows you to set the fixture’s RDM PID code.
w Access the menu by pressing the “Mode Esc” key.
w Use the up/down arrow keys to access the “OPTION” menu and press
“Enter.” Then use the left/right arrow keys to select “Service Pin.”