manualshive.com logo in svg

AXXIS KLINCH-PAK KP-APN-22, Manual, Page: 3 / 12

Share
Download
AXXIS KLINCH-PAK KP-APN-22 Manual Download Page 3

 3 

1320 Tower Road  Schaumburg, IL  60173 

Phone:  

888-392-9947

   Fax:  

877-393-2948

 

 

 

PAGE

 

TOOL SPECIFICATIONS ....................................................................................................................... 4 

 

SAFETY INSTRUCTIONS ...................................................................................................................... 5 

 

LUBRICATION AND MAINTENANCE .................................................................................................... 6 

 

ADJUSTING FOR STAPLE LEG LENGTH ............................................................................................ 6 

 

CLINCH ADJUSTMENT .......................................................................................................................... 7 

 

DEPTH ADJUSTMENT ........................................................................................................................... 7 

 

EXPLODED VIEW OF TOOL .................................................................................................................. 8 

 

PARTS LIST ............................................................................................................................................ 9 

 

TROUBLE SHOOTING ......................................................................................................................... 10 

TABLE OF CONTENTS 

Summary of Contents for KLINCH-PAK KP-APN-22













Reviews:

No comments