Axxess GMOS-LAN-06 Installation Instructions Download Page 3

3

REV. 7/3/2018 INSTGMOS-LAN-06

With the key in the off position:

  •  Connect the 16-pin harness with stripped leads, and the GMOS-LAN-06 harness, into the 

interface.

Attention!

 Do not connect the GMOS-LAN-06 harness to the wiring harness in the vehicle just yet.

For the steps below, the L.E.D. located inside the interface can only be seen while active. The 
interface does not need to be opened to see the L.E.D.

1.

  Start the vehicle.

2.

  Connect the GMOS-LAN-06 harness to the wiring harness in the vehicle. The L.E.D. will initially be 

Green

 to indicate the interface is powered.

3.

  After a few seconds the L.E.D. will turn on solid 

Red

 while the interface automatically programs 

to the vehicle. The radio will shut off at this point. This process should take 5 to 30 seconds.

4.

  After the interface is programmed, the L.E.D. will turn on solid 

Green

, and the radio will come 

back on, indicating programming was successful.

5.

  Test all functions of the installation for proper operation, before reassembling the dash.

6. 

If the interface fails to function, refer to “Troubleshooting”.

Resetting the Axxess interface
1.

  The 

Blue

 reset button is located inside the Axxess interface, between the two connectors. 

The button is accessible outside the Axxess interface, no need to open the Axxess interface.

2.

  Press and hold the reset button for two seconds, then let go to reset the Axxess interface.

3.

  Refer to “Programming the Axxess Interface” from this point.

OnStar level adjustment

  •  To adjust the OnStar volume level find the 

Black/Yellow

 wire on the 12-pin harness. 

  •  Push the 

Blue

 OnStar button: while the voice is speaking tap the 

Black/Yellow

 wire to 

ground. 

  • 

There are 4 volume settings for OnStar:

 Once the 4th setting is reached and the 

Black/

Yellow

 wire is tapped to ground, it will automatically go back to the first volume setting. 

  •  Once the volume is set it will stay at that volume until the 

Black/Yellow

 wire is tapped to 

ground again.

INSTALLING THE GMOS-LAN-06

PROGRAMMING THE GMOS-LAN-06

TROUBLESHOOTING

ADJUSTING THE GMOS-LAN-06

Summary of Contents for GMOS-LAN-06

Page 1: ...ping tool and connectors or solder gun solder and heat shrink Tape Wire cutter Zip ties TABLE OF CONTENTS Connections to be made 2 Installing the GMOS LAN 06 3 Programming the GMOS LAN 06 3 Adjusting the GMOS LAN 06 3 Troubleshooting 3 Saturn OnStar interface 2006 2007 APPLICATIONS Provides accessory power 12 volt 10 amp Maintains the retained accessory power R A P feature Retains OnStar OE Blueto...

Page 2: ...n Blue Pink Blue White Green Green Black Green Purple Light Green Orange White Purple Purple Black From the GMOS LAN 06 harness to the aftermarket radio Connect the Yellow wire to the 12 volt constant battery wire Connect the Black wire to the ground wire Connect the Orange wire to the illumination wire If no illumination wire is present tape it off and disregard it Connect the Green wire to the l...

Page 3: ...l 5 Test all functions of the installation for proper operation before reassembling the dash 6 If the interface fails to function refer to Troubleshooting Resetting the Axxess interface 1 The Blue reset button is located inside the Axxess interface between the two connectors The button is accessible outside the Axxess interface no need to open the Axxess interface 2 Press and hold the reset button...

Page 4: ...fied technicians IMPORTANT If you are having difficulties with the installation of this product please call our Tech Support line at 1 800 253 TECH Before doing so look over the instructions a second time and make sure the installation was performed exactly as the instructions are stated Please have the vehicle apart and ready to perform troubleshooting steps before calling AxxessInterfaces com CO...

Reviews: