background image

CAUTION! 

 All accessories, switches, climate 

controls panels, and especially air bag indicator 

lights must be connected before cycling the 

ignition. Also, do not remove the factory radio 

with the key in the on position, or while the 

vehicle is running. 

AXDIS-TY2

I N S TA L L AT I O N I N S T R U C T I O N S

AxxessInterfaces.com 

© COPYRIGHT 2020 METRA ELECTRONICS CORPORATION 

REV. 1/23/20 INSTAXDIS-TY2

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape 
• Connectors (example: butt-connectors, bell 
caps, etc.) • Small flat-blade screwdriver

TABLE OF CONTENTS

Connections to be made ....................................2-3
- 3.5mm jack steering wheel control retention ...3
Installing the AXDIS-TY2 ........................................3
Programming the AXDIS-TY2 ................................4
Adjusting the AXDIS-TY2 .......................................4
Steering wheel control settings ........................5-7
- L.E.D. feedback ....................................................5
- Changing radio type ...........................................5
- Remapping the steering wheel control buttons ...6
- Dual assignment instructions (long button press) ...7
Troubleshooting .....................................................8

Toyota 

Amp Interface with SWC

 

2012-Up*

APPLICATIONS

•  Retains audio controls on the 

steering wheel

•  Provides NAV outputs (reverse)
•  Retains the factory AUX-IN jack

•  Designed for amplified models
•  Retains balance
•  Micro-B USB updatable

TOYOTA

Avalon * 

2013-Up

4-Runner 

2014-Up

Camry 

2014-2017

Camry (w/ nav) 

2012-2013

Highlander 

2014-Up

Prius 3rd Gen (w/ nav)  2012-2015
Plug-In (PHV) (w/ nav)  2012-2015
Prius V 

2012-2017

Rav-4 

2014.5-Up

Sequoia 

2014-Up

Sequoia (w/ nav) 

2013

Sienna 

2015-Up

Tacoma 

2014-Up

Tundra * 

2014-Up

Venza 

2015

Venza (w/ HDD based nav) 2013-2014

• AXDIS-TY2 interface
• AXDIS-TY2 harness
• Female 3.5mm connector with stripped lead

*Visit 

AxxessInterfaces.com

 for up-to-date vehicle specific applications.

* Only for models with a JBL amplifier 

Summary of Contents for AXDIS-TY2









Reviews: