background image

10

Specifications 

CEA-2006 Power Standard Specifications

(reference: 14.4VDC, 20Hz~20kHz)

Power Out

put

 (14.4VDC, 20Hz ~ 20kHz):  

   350 Watts x 1 channel @ 4 ohms and ≤ 1% THD+N
   650 Watts x 1 channel @ 2 ohms and ≤ 1% THD+N

Peak Music Power Output: 

1750 Watts

 

Signal to noise ratio:

 

70dBA (reference: 1 watt into 4 ohms)

Frequency response:

 20Hz - 150Hz 

Amplifier dimensions:

 1.58" x 4.7" x 9" 

CEA-2006 Power Standard Specifications

(reference: 14.4VDC, 20Hz~20kHz)

Power Out

put

 (14.4VDC, 20Hz ~ 20kHz):  

   90 Watts x 2 channels @ 4 ohms and ≤ 1% THD+N
   120 Watts x 2 channels @ 2 ohms and ≤ 1% THD+N
   280 Watts x 2 channels @ 4 ohms (bridged) and ≤ 1% THD+N

Peak Music Power Output: 

900 Watts @ 4 ohms

Signal to noise ratio:

 

90dBA (reference: 1 watt into 4 ohms)

Frequency response:

 10Hz - 35kHz 

Amplifier dimensions:

 2.1" x 9.7" x 9"

CEA-2006 Power Standard Specifications

(reference: 14.4VDC, 20Hz~20kHz)

Power Out

put

 (14.4VDC, 20Hz ~ 20kHz):  

   100 Watts x 4 channels @ 4 ohms and ≤ 1% THD+N
   150 Watts x 4 channels @ 2 ohms and ≤ 1% THD+N
   260 Watts x 2 channels @ 4 ohms (bridged) and ≤ 1% THD+N

Peak Music Power Output: 

2000 Watts @ 4 ohms

Signal to noise ratio:

 70dBA (reference: 1 watt into 4 ohms)

Frequency response:

 10Hz - 35kHz 

Amplifier dimensions:

 1.58" x 4.7" x 9"

AXA10D

AXA20

AXA40D

OPERATION

Summary of Contents for AXA10D













Reviews: