Get to know us at: www.axvue.com
AXVUE E662 Video Baby Monitor
with Two Way Communication & Temperature
Tools required for wall mount: Screwdriver and drill (not included)
Keep this instruction manual for future reference.
For technical support see FAQ page.
For adult use only.
Please read the following instructions and warnings carefully
Model- E662
INSTRUCTION MANUAL
STRANGULATION HAZARD - Children have STRANGLED in cords.
Keep this cord out of reach of children (more than 3 feet away
from the crib). Use enclosed Security Clips to help secure cord
away from baby’s reach. Never use extension cords with AC
adapters. Only use the AC adapters provided.
WARNING
Features and components
(continued)
CAMERA
1 Nighttime LEDs
2 Lens
3 Power Indicator
4 Microphone
5 Speaker
6 Power / Code
7 Temperature Sensor
8 DC Jack
x2
x2
x12
Adapter for camera:
Step1:
Turn camera power on by pressing and
holding Power / Code ‘ ’button until
the power indicator lights.
Step2:
Press and hold Power / Video
button on monitor for 5 seconds until the
AXVUE showed on the screen. Video should
immediately appear on screen.
If video does not appear, go to ‘To pair monitor
and camera’. If video appears, the initial set up
test is completed, and you can install camera
according to the instructions below.
Install Camera:
Place the camera on a flat
surface, such as a bureau or shelf (Figure1) or
mount the camera on a wall (Figure 2). For
example: On the desk or cabinet or fixed to the
wall, make sure that at least 3 feet from the
crib, power line should be placed above or
behind the camera, adjust the camera angle
until the display see the entire crib, or the best
line of sight you think.
Before using the monitor, charge the battery for 6-8 hours.
3 feet
Figure 1
Fixing cable
with clip
3 feet
Figure 2
WALL-MOUNT
1. Pre-drill a hole in the wall, a 3/16” (4.8mm) drill bit.
2. Insert the wall anchor into the hole and with a hammer, tap gently on the
end until the wall anchor is flush with the wall.
3. Tighten screw until only 1/4” (6.2mm) of the screw is exposed.
4. Insert camera adapter into the camera’s adapter jack.
5. Slide the back of the camera down onto the screw until the camera is secure to the wall.
6. Plug the adapter into a standard electrical outlet.
7. Secure the cord to the wall by using the security clips to keep cord away from baby’s reach.
Setup & use
1 Power / Video
2 LED*
3 Left
4 Talk Back / Zoom
5 Menu / OK
6 Speaker
7 Right
8 Volume Up
9 Volume Down
10 Microphone
11
Battery Compartment
12 Kickstand
13 DC Jack
Power & Low Battery
Sound Lights
*LED
Adapter for monitor:
Features and components
MONITOR
STRANGULATION HAZARD
- Children have STRANGLED in cords. Keep this cord out of reach of
children (more than 3 feet away from the crib). Use enclosed Security Clips to help secure cord
away from baby’s reach. Never use extension cords with AC adapters. Only use the AC adapters
provided.
WARNING:
-Use only the original rechargeable battery provided. Please contact AXVUE INC. for replacement
battery. Contact information can be found on last page of these instructions.
-Clean battery and product contacts prior to battery installation.
-Do not short-circuit supply terminals.
-Remove battery when product is stored for long periods of time or when battery is exhausted.
-Keep all batteries away from children.
-Dispose of exhausted battery properly.
BATTERY WARNING
WARNING
-Strangulation Hazard - Children have STRANGLED in cords. Keep this cord out of reach of children
(more than 3 feet away from the crib). Use enclosed Security Clips to help secure cord away from
baby’s reach. Never use extension cords with AC adapters. Only use the AC adapters provided.
-When an adapter is plugged into an electrical outlet, do not touch the exposed end.
-Test monitor before first use, periodically, and when changing location of the camera.
-Do not use monitor near water (such as bathtub, sink, etc.).
-Keep monitor away from heat sources (such as stoves, radiators, etc).
Make sure there is proper ventilation around all monitor components. Do not place on sofas,
cushions, beds, etc. which may block ventilation.
-This product is not a toy. Do not allow children to play with it. This product contains small parts.
Adult assembly required. Exercise care when unpacking and assembling the product.
THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT SUPERVISION.
WARNING
TO USE PLUGGED-IN MODE
Step 1: Place the monitor in the room from which you want to monitor your baby (ie., living room or
bedroom). Plug the monitor AC adapter into the AC adapter jack and other end into standard
electrical outlet.
Step 2: Press and hold Power / Video button for 5 seconds to power up until the AXVUE logo or
video appears on screen.
Step 3: For audio and no video, press the Power / Video button.
Step 4: To turn the monitor off completely, press and hold the Power / Video button for 5 seconds.
TO USE PORTABLE / BATTERY MODE
Step 1: Charge the battery for 6 hours at least before using the monitor in portable mode.
Step 2: Make sure camera adapter is plugged into the camera.
Step 3: The battery life can be up to 8 hours if fully charged.
Before using the monitor, charge the battery for 6-8 hours.
TO PAIR MONITOR AND CAMERA ( ADD A CAMERA )
Battery life will be weakened if recharging constantly. Remove battery if long time of non-use, or exhausted.
Red LED will flash
The monitor and the camera are paired prior to the shipment. If the monitor and camera are
found not paired for some reason, follow steps below:
Step 3: Press Power / Video for 5 seconds to power on the monitor.
Step 5: Using the Left or Right to highlight ADD CAM and press
Menu / OK
to confirm.
Step 6: Choose the identifying number to be assigned on the camera.
Step 7: Press the Menu / OK
button again to start pairing and the red light will flash.
Step 4: Press Menu / OK shortly to enter menu, then press Right
to highlight the camera option
function
and Menu / OK
to confirm.
Step 1: Make sure the monitor is at the same area with the camera.
Step 2: Make sure the camera AC adapters are plugged in.
Step 9: Waiting 3 seconds, the green light stop flashing once paired successfully and the video will appear.
Step 8: Press Power/Code ‘ ’on the camera until the power indicator flashes.
VOX
1
1
2
3
4
