Axminster Trade UB-802 User Manual Download Page 4

 

2

 

Wood working can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved 

with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if 

normal safety precautions are overlooked or ignored, personal injury to the operator may result. 

Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust masks and hearing protection can reduce your potential for 

injury. But even the best guard won’t make up for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the 

workshop. If a procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels safer. REMEMBER: Your personal safety is your 

responsibility.  

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY 

 

1.

 

FOR YOUR OWN SAFETY, READ INSTRUCTION 
MANUAL BEFORE OPERATING THE TOOL. Learn the 
tool’s application and limitations as well as the specific hazards 
peculiar to it. 

2.

 

KEEP GUARDS IN PLACE and in working order 

3.

 

ALWAYS WEAR EYE PROTECTION 

4.

 

GROUND ALL TOOLS. If tool is equipped with three-prong 
plug, it should be plugged into a three-hole electrical 
receptacle. If an adapter is used to accommodate a two-prong 
receptacle, the adapter plug must be attached to a known 
ground. Never remove the third prong. 

5.

 

REMOVE ADJUSTING KEYS AND WRENCHES. Form 
habit of checking to see that keys and adjusting wrenches are 
removed from tool before turning it “ON”. 

6.

 

KEEP WORK AREA CLEAN. Cluttered areas and benches 
invite accidents. 

7.

 

DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use 
power tools in damp or wet locations, or expose them to rain. 
Keep work area well lighted. 

8.

 

KEEP CHILDREN AND VISITORS AWAY. All children and 
visitors should be kept a safe distance from work area. 

9.

 

MAKE WORKSHOP CHILDPROOF – with padlocks, master 
switches, or by removing starter keys. 

10.

 

DON’T FORCE TOOL. It will do the job better and be safer at 
the rate for which it was designed. 

11.

 

USE RIGHT TOOL. Don’t force tool or attachment to do a job 
for which it was not designed.   

12.

 

WEAR PROPER APPAREL. No loose clothing, gloves, 
neck-ties, rings, bracelets, or other jewelry to get caught in 
moving parts. Non-slip footwear is recommended. Wear 
protective hair covering to contain long hair. 

13.

 

ALWAYS USE SAFETY GLASSES. Wear safety glasses. 
Everyday eyeglasses only have impact resistant lenses; they are 
not safety glasses. Also use face or dust mask if cutting 
operation is dusty.   

14.

 

SECURE WORK. Use clamps or a vise to hold work when 
practical. It’s safer than using your hand and frees both hands to 
operate tool. 

15.

 

DON’T OVERREACH. Keep proper footing and balance at all 
times. 

16.

 

MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp 
and clean for best and safest performance. Follow instructions 
for lubricating and changing accessories. 

17.

 

DISCONNECT TOOLS before servicing and when changing 
accessories such as blades, bits, cutters, etc. 

18.

 

USE RECOMMENDED ACCESSORIES. The use of 
accessories and attachments not recommended by us may 
cause hazards or risk of injury to persons. 

19.

 

REDUCE THE RISK OF UNINTENTIONAL STARTING. 
Make sure switch is in “OFF” position before plugging in 
power cord. 

20.

 

NEVER STAND ON TOOL. Serious injury could occur if the 
tool is tipped or if the cutting tool is accidentally contacted. 

21.

 

CHECK DAMAGED PARTS. Before further use of the tool, a 
guard or other part that is damaged should be carefully checked 
to ensure that it will operate properly and perform its intended 
function – check for alignment of moving parts, binding of 
moving parts, breakage of parts, mounting, and any other 
conditions that may affect its operation. A guard or other part 
that is damaged should be properly repaired or replaced. 

22.

 

DIRECTION OF FEED. Feed work into a blade or cutter 
against the direction of rotation of the blade or cutter only. 

23.

 

NEVER LEAVE TOOL RUNNING UNATTENDED. TURN 
POWER OFF. Don’t leave tool until it comes to a complete 
stop. 

24.

 

DRUGS, ALCOHOL, MEDICATION. Do not operate tool 
while under the influence of drugs, alcohol or any medication. 

25.

 

MAKES SURE TOOL IS DISCONNECTED FROM POWER 
SUPPLY while motor is being mounted, connected or 
reconnected. 

26.

 

WARNING: The dust generated by certain woods and wood 
products can be injurious to your health. Always operate 
machinery in well ventilated areas and provide for proper dust 
removal. Use wood dust collection systems whenever possible.

 

 

IMPORTANT SAFETY RULES FOR DUST COLLECTORS   

Summary of Contents for Trade UB-802

















Reviews: