Axis F34 User Manual Download Page 8 | Manualshive

Page: 8 / 64

Axis F34 User Manual Download Page 8

AXIS F34 Main Unit

Hardware Overview

Connectors and Buttons

For technical specifications, see

Network Connector

RJ45 Ethernet connector with Power over Ethernet (PoE).

NO

NO

NOTICE

TICE

TICE

The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network shall
be intended for their specific use. Make sure that the network devices are installed in accordance with the manufacturer’s
instructions. For information about regulatory requirements, see

Electromagnetic Compatibility (EMC) on page 2

.

Power Connector

2-pin terminal block for power input. Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either a rated
output power limited to

≤

100 W or a rated output current limited to

≤

5 A.

RJ12 Connector

The RJ12 connector is used for connecting the sensor unit to the main unit.

For information on how to shorten the sensor unit cable see

Shorten Sensor Unit Cable on page 9

.

SD Card Slot

NO

NO

NOTICE

TICE

TICE

• Risk of damage to SD card. Do not use sharp tools or excessive force when inserting or removing the SD card.

• Risk of data loss. To prevent data corruption, the SD card should be unmounted before removal. To unmount, go to

Setup >

System Options > Storage > SD Card

and click

Unmount

.

This product supports SD/SDHC/SDXC cards (not included).

For SD card recommendations, see

www.axis.com

Control Button

For location of the control button, see

Hardware Overview on page 7

The control button is used for:

•

Resetting the product to factory default settings. See

.

•

Connecting to an AXIS Video Hosting System service. See

. To connect, press and hold the button for about 3

seconds until the Status LED flashes green.

•

Connecting to AXIS Internet Dynamic DNS Service. See

. To connect, press and hold the button for about 3 seconds.

LED Indicators

Note

• The Status LED can be configured to be unlit during normal operation. To configure, go to

Setup > System Options > Ports

& Devices > LED

. See the online help for more information.

• The Status LED can be configured to flash while an event is active.

• The Status LED can be configured to flash for identifying the unit. Go to

Setup > System Options > Maintenance

.

8

«
...
6
7
8
9
10
...
»

Summary of Contents for F34

































































Reviews:

No comments