Specification
Model
Axion 10.8 Drill Driver
Rating
Trade
Speed
0 - 300, 0 - 1050rpm
Torque and Settings
15Nm/17 + Drill mode
Chuck Cap/Type
10mm Jacobs Keyless
Max Capacity Steel
8mm
Max Capacity Wood
10mm
Battery No/Capacity
2 x 1.3Ah
Battery Voltage/Type
10.8V Li-Ion
Charge Time
60 mins
Weight
1kg
Drill operation
Inserting the battery
Set rotation direction switch (5) to centre position to avoid
unintentional starting. Insert charged battery (7) into
handle so that it is felt to engage and is flush with the drill.
Rotation direction
The rotation direction slide switch (5) is used to change
the rotational direction of the drill. Push the switch fully to
the left for forward (clockwise) rotation or to the right for
reverse (anticlockwise) rotation. Ensure that the slide
switch is pushed fully home in whichever direction,
otherwise you cannot depress the trigger switch. Similarly
you cannot move the slide switch whilst the trigger switch
is depressed. A useful side effect of this interlock can be
utilised during tool changing; if you move the rotation
selector to its half-way position, you cannot inadvertently
switch the tool on.
Setting the torque
The torque presetting ring (1) can be rotated to select any
one of 17 torque settings – with the correct setting the
drill will stop when the screw is flush with the material.
Align the number on the ring with the arrow on the body
to select the required torque.
Drill selection
The safety clutch (torque) is deactivated when the ‘drill’
action is selected. The ‘drill’ (anticlockwise) selection may
also be used for unscrewing.
Gear selection
A slide switch (2) enables you to select high or low gears –
only engage when the drill is at a standstill. If you
experience difficulty moving the gear selector to the fully
engaged positions, lightly rotate the drill chuck.
On/Off switch and speed control
The On/Off switch (6) provides electronic speed control of
your drill – the further switch is depressed the greater the
speed dependent on the torque/drill setting. If you
experience difficulty depressing the On/Off switch, check
the rotation selector (5) is fully engaged. Also, the work
area LED light (4) is lit when the On/Off switch is pressed.
Auto-lock
When the On/Off switch (6) is not activated and a bit is
located in the chuck (3), the drill spindle/tool holder is
locked. This will enable the drill to be used as a screwdriver
even when the power is off or the battery is flat.
Run-on brake
When the On/Off (6) switch is released the chuck will
automatically brake to a stop – there will be no run-on so
giving greater accuracy and safety in use.
Torch operation
Dual work lights
The torch has two lighting settings operated by the single
switch (10) – press once for main beam (9), press again for
the side light (11), then again for Off.
Battery charger operation
Charging
Connect mains plug of charger into mains socket – a red
LED light (12) indicates the charger is ready to use. Insert
battery into the charging compartment (8) – a green LED
light (12) will commence flashing indicating the battery is
being charged. A discharged battery will take
approximately 60 mins to fully charge – continuous
lighting of the green LED signals that the battery is fully
charged and may be removed.
Declaration of Conformity
Licence Holder:
Ningbo Hanpu Tools Co. Ltd., Gangtou
Middle Street, Hengxi Town, Yinzhou District, Ningbo
Zhejiang 315135, P. R. China.
Registration No:
AE 50185676 0001
Report No:
15038883 0001
Tested:
EN 55014-1 : 2006 and EN 55014-2 : 1997+A1+A2
Conforms with all provisions of Annex 1
of the Council Directive 2004/108/EC.
