AXIOMTEK MANO520 Series User Manual Download Page 17

Page: 17 / 59

MANO520 Mini ITX Motherboard

Board and Pin Assignments

2.4

Connectors

Signals go to other parts of the system through connectors. Loose or improper connection
might cause problems, please make sure all connectors are properly and firmly connected.
Here is a summary table showing connectors on the hardware.

Connector

Description

CN1

DIMM1: DDR4 SO-DIMM Connector

CN2

DIMM2: DDR4 SO-DIMM Connector

CN3

DisplayPort Combo Connector

CN5

SIM Card Socket

CN6

mSATA Connector

CN7~CN9

SATA 3.0 Connectors

CN12

Front Panel Header

CN13

USB 2.0 port

CN14

USB 2.0 Wafer Connector

CN15

PCI-Express x16 Slot

CN16~CN17

ATX Power Input Connectors

CN18~CN19

Fan Connectors

CN20

GPIO Header

CN21

COM1 and COM2 D-Sub Connector

CN22~CN23

COM3 and COM4 Wafer Connectors

CN26~CN27

LAN and USB 3.0 Connectors

CN28

Audio Jack

CN29

Front Audio Connector

CN30

HDMI Connector

CN31

LVDS Signal Header

CN32

LVDS Backlight Control Header

CN34

M.2 Key E Connector

Summary of Contents for MANO520 Series




























































Search results

Summary of Contents for MANO520 Series

Reviews:

Related manuals for MANO520 Series

Brands by name

Popular brands

AXIOMTEK MANO520 Series, User Manual

Search results

Summary of Contents for MANO520 Series

Reviews:

Related manuals for MANO520 Series

Brands by name

Popular brands