manualshive.com logo in svg

AXIOMTEK IMB200, User Manual

Share
Download
AXIOMTEK IMB200 User Manual Download Page 57

IMB200 LGA775 ATX MB User Manual 

 

Award Bios Utility 

51 

 

 
 

z

 

On-Chip Primary PCI IDE 

This option could allow you to enable or disable the primary 
and secondary IDE controller, select Disabled if you want 
to add a Different hard drive controller. 

z

 

IDE Primary Master PIO 

This option could allow you to set up Master IDE interface 
from PIO mode0 to PIO Mode 4 

z

 

IDE Primary Slave PIO 

 This option could allow you to set up Slave IDE interface 
from PIO mode0 to PIO Mode 4 

z

 

IDE Primary Master UDMA 

This option could allow you to enabled or disabled onboard 
Ultra DMA mode on Primary Master  

z

 

IDE Primary Slave UDMA 

This option could allow you to enabled or disabled onboard 
Ultra DMA mode on Primary Slave  
  

z

 

On-Chip Secondary PCI IDE 

This option could allow you to enabled or disabled onboard 
Secondary PCI IDE controller  

z

 

IDE Primary Master PIO 

Summary of Contents for IMB200














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands