manualshive.com logo in svg

AXIOMTEK GOT3217WL-845-PCT, User Manual

Share
Download
AXIOMTEK GOT3217WL-845-PCT User Manual Download Page 8

GOT3217WL-845-PCT 

User’s Manual

 

2 

 

Introduction

 

 

 

WLAN antenna supported (optional) 

 
The GOT3217WL-845-PCT comes with 2 PCI Express Mini Card slots as an add-on option to 
connect  s  a  wireless  LAN  card  under  802.11  a/b/g/n  protocols,  or  with  other  3G/GPRS 
applications, etc. These slots also come with 3 optional fixed rotational WLAN/3G antennas for 
wireless network connection.   
 

 

Multi- PCAP touch surface of 7H hardness 

 
The  GOT3217WL-845-PCT  is  designed  with  a  user  friendly  multi-  PCAP  touch.  Users  can 
operation  it  with  direct  touch.  The  surface  hardness  is  up  to  7H,  good  for  applications  of 
anti-scratch purpose. 
 

 

Other features 

 
The GOT3217WL-845-PCT utilizes one 204-pin DDR3L SODIMM system memory up to 8GB 
at the maximum, one SATA HDD and one mSATA. It provides an over-current protection-fuse 
and a full set of I/O including RS-232/422/485, USB 2.0, USB 3.0, audio (line-out), and Gigabit 
Ethernet. Additionally, this slim unit supports panel mount as the standard installation, as well 
as optionally wall mount, VESA mount and desktop stand mount. 
 

1.2  Specifications 

 

Main CPU Board 

 

 

CPU 

 

Intel®  Pentium®  Processor N3710 (2M Cache, up to 2.56 GHz) onboard 

 

 

System Memory 

 

1 x 204-pin DDR3L SO-DIMM socket 

 

Maximum memory up to 8GB 

 

 

BIOS 

 

AMI UEFI BIOS 

 

I/O System 

 

 

Standard I/O 

 

2 x RS-232/422/485 

 

2 x USB 2.0 

 

2 x USB 3.0 

 

 

Ethernet 

 

2 x RJ45 for Gigabit Ethernet (Intel i211AT) 

 

 

Audio 

 

1x Line-out

 

 

 

Expansion 

 

1 x Mini-card slot (w/SIM slot) 

 

1 x Mini-card slot (supports mSATA, optional) 

 

 

Storage 

 

1 x 2.5” SATA   

 

1 x mSATA 

Summary of Contents for GOT3217WL-845-PCT













































Reviews:

No comments

Brands by name

Popular brands

Load more brands