background image

CAPA831 Intel

® 

Atom

TM

 D2550/N2800/N2600 Processor 3.5” SBC

 

2  

Introduction

 

 

1.2 Specifications 

 

 

CPU 

 

Intel

®

 Atom

TM

 dual core D2550 1.86 GHz. 

 

Intel

®

 Atom

TM

 dual core N2800 1.86 GHz. 

 

Intel

®

 Atom

TM

 dual core N2600 1.6 GHz 

 

 

Thermal Solution 

 

With Atom

TM

 dual core D2550 1.86 GHz; fan solution. 

 

With Atom

TM

 dual core N2800 1.86 GHz or dual core N2600 1.6GHz; fanless solution 

 

 

System Chipset 

 

Intel

®

 NM10 chipset. 

 

 

BIOS 

 

American Megatrends Inc. UEFI (Unified Extensible Firmware Interface) BIOS. 

 

16Mbit SPI Flash, DMI, Plug and Play. 

 

RPL/PXE Ethernet Boot ROM. 

 

 

System Memory 

 

One 204-pin unbuffered DDR3 SO-DIMM socket. 

 

Maximum to 4GB DDR3 1066MHz memory for D2550/N2800. 

 

Maximum to 2GB DDR3 800MHz memory for N2600. 

 

 

Onboard Multi I/O 

 

Controller: Nuvoton NCT6627UD. 

 

Serial Ports: Two ports for RS-232/422/485 and two ports for RS-232. 

 

 

Serial ATA 

 

One SATA-300 connector. 

 

 

CFast™ Socket 

 

One CFast™ socket. 

 

 

USB Interface 

 

Six USB ports with fuse protection and complies with USB Spec. Rev. 2.0. 

 

 

Display 

 

A slim type 15-pin D-Sub connector as VGA connector. 

 

One 40-pin connector for 18/24-bit single/dual channel LVDS and one 8-pin inverter 
connector. For N2600/N2800, LVDS resolution is up to 1600x1200 in 24-bit dual 
channel. For D2550, LVDS resolution is up to 1920x1200 in 24-bit dual channel. 

 

One DisplayPort. 

 

 

Trusted Platform Module (TPM) 

 

Controller: Infineon SLB9635 via LPC bus interface. 

 

Complies with TPM1.2 main and PC client specification. 

 

 

Watchdog Timer 

 

1~255 seconds or minutes; up to 255 levels. 

 

 

Ethernet 

 

Two ports with Intel

®

 82583V for Gigabit/Fast Ethernet. 

 

 

Audio 

 

HD audio compliant (with speaker/line-out and line-in/MIC-in) with Realtek ALC662. 

 

Speaker/line-out and line-in/MIC-in via box header connector. 

 

Summary of Contents for CAPA831













































































Reviews: