Manufacturer
AXING AG
Gewerbehaus Moskau
8262 Ramsen
EEA contact address
Bechler GmbH
Am Rebberg 44
78239 Rielasingen
State of the art 2020-04-15
Technical improvements, changes in design, printing- and other errors expected.
Technical data:
Type
SES 544-06
Inputs
Number
5
Frequency range
5…862 MHz @ TERR
250…2350 MHz @ SAT
LNB voltage
12 V
Max. LNB current
500 mA per LNB
1000 mA total
Level (AGC)
60… 90 dBµV
Isolation V | H.
30 dB
Subscriber ports
Number
4
Supported standards
EN 50494, EN 50607
Tap loss TERR
17 dB ±2,0 dB
Frequency range (SAT)
950…2150 MHz
User bands
4 × 4
User band frequencies
1331/1382/1433/1484 MHz
Output level SAT (SCR/CSS)
91 dBµV ±2,0 dB
Output level SAT (Legacy)
83 dBµV ±2,0 dB
Current consumption from STB (SCR/
CSS)
180 mA
Current consumption from STB (Legacy)
60 mA
Trunk outputs
Number
5
Through loss TERR
2 dB ±2,0 dB
Through loss SAT
4 dB ±2,0 dB
Connectors
Connector type
F
Return loss
≥ 10 dB
General
Equipotential bonding connection
4 mm²
Operating temperature range
(acc. to EN 60065)
-20…70°C
Dimensions (W × H × D) appr.
140 x 140 x 63 mm
Weight
0,394 kg
SES 544-06
premium
-line
Single cable multiswitch II (SCR)
Operation instructions
CE Confirmation Declaration
Hereby, AXING AG declares that the device is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address:
https://axing.com/en/downloads/ce/
.
WEEE Nr. DE26869279 | Electrical and electronic components must not be disposed of
as residual waste, it must be disposed of separately.
Safety advices:
Installation and repairs to the equipment may only be carried out by
technicians observing the current guidelines. No liability will be assumed
in the case of faulty installation and commissioning.
Before handling the device, disconnect the power supply, otherwise there
is danger to life. This also applies if you clean the device or work on the
connections.
If a replaceable fuse is available, pull the mains plug before changing
the fuse. Replace damaged fuses only with standard fuses of the same
nominal value.
The equipment may only be operated in dry rooms. In humid rooms or
outdoors there is danger of short-circuit (caution: risk of fire) or
electrocution.
To prevent damage to your equipment and to avoid possible peripheral
damages, mount the device only on flat surfaces.
Choose the location of installation or mounting such that children may
not play unsupervised near the equipment and its connections.
The location of installation or mounting must allow a safe installation of
all cables connected. Connected cables must not be damaged or crushed
by any objects.
Absolutely avoid that cables come near any source of heat (e.g.
radioators, other electrical devices, chimney, etc.).
Choose the location of installation or mounting so that under no
circumstances liquids or objects can get into the equipment (e.g.
condensation, water coming from leaking roofs or flowing water, etc.).
Avoid exposure of the equipment to direct sunlight and to other heat
sources (e. g. radiators. other electrical devices, chimney, etc.).
Devices that are equipped with heat sinks or ventilation slots must under
no circum-stances be covered or blocked. Also ensure for a generous air
circulation around the equipment. In this way you avoid possible damage
to the equipment as well as a risk of fire caused by overheating.
In case of damage, interrupt the power supply immediately.
Do not try to repair the device. This device should only be serviced or
repaired by qualified service personnel. Contact your distributor for more
information.
Do not open the device.
For disassembly always pull the mains plug first and disconnect the
power supply cable from the connected device.
