instAllAtion witH AxiA PowerstAtion
instAllAtion witH AxiA studioenGine
network ConFiGurAtion witH AxiA PowerstAtion
1. Boot the PowerStation, a setup screen (I) will
appear on the connected video monitor. An IP
address is needed.
2. Tap the up arrow key on the attached keyboard until
the “Config IP addr” value is in yellow text.
3. Clear the current value with the Backspace key on
the attached keyboard and use number keys to
enter a new value. Make a note of this IP address
for further configuration in later steps.
4. Tap the arrow keys on the attached keyboard
to navigate to “Config NetMask” and “Config
Gateway”, enter the needed values.
5. Tap the down arrow key on the attached keyboard
to navigate to “Save & Reboot”. Tap the Enter key on
the attached keyboard to reboot system.
6. Disconnect USB keyboard from PowerStation.
I
I
J
K
L
instAllAtion HelP
If you have more questions, you can access the full manual online at
http://www.telosalliance.com/Axia/Fusion or call the Telos Alliance
24/7 Support Team at +1 (216) 622-0247, we’d be happy to help you out.
Continue to tHe system ConFiGurAtion
The Console is now recognized by the network and is
ready to be linked to the StudioEngine and configured
to load sources. Continue to the “System Configuration”
instructions.
Continue to tHe system ConFiGurAtion
The Console is now recognized by the network and is
ready to be linked to the PowerStation then configured
to load sources. Continue to the “System Configuration”
instructions.
network ConFiGurAtion witH AxiA studioenGine
1. Apply Power to the StudioEngine. The front display
should indicate an error due to sync issue-this is
normal. An IP address is needed.
2. Tap the rotary encoder knob (I) on the front panel for
a menu view, rotate knob until “Engine IP settings”
(J) is highlighted, tap knob to select.
3. Rotate knob (I) to select “Net Address” and tap knob
to select.
4. Once on the Engine IP settings screen (K), rotate
knob (I) to move the cursor, tap knob to edit cursor
position, rotate to increment value, tap knob to
accept change. Repeat for all IP address values. Make
a note of this IP address for further configuration in
later steps.
5. Select check mark to right of address and tap knob
(I) to accept.
6. Repeat for Netmask and Gateway as needed.
7. Select Console (L) and change the option to Fusion.
8. Select OK and tap knob to respond affirmative in
order to reboot engine with new settings.
1. Tilt the overbridge panel of the Fusion Console (A) forward (toward faders) to gain access to the
Fusion Console overbridge board.
2. Connect one end of the 6-Pin molex power cable supplied with the PowerStation to the Surface
port (B) on the PowerStation. Connect the other end to the power port on the Fusion Console
overbridge board (C).
3. Connect Ethernet cable to the network connection port on the Fusion Concole overbridge board
(D), connect other end to an available network port on the PowerStation (E).
4. Connect 1080p monitor to the DVI-D video port (F) on the PowerStation.
5. Connect USB keyboard to USB port (G) on the PowerStation.
6. Close the Fusion Console overbridge panel.
7. Continue to Network Configuration with Axia PowerStation.
PHysiCAl ConneCtions witH AxiA PowerstAtion
1. Tilt the overbridge panel of the Fusion Console (A) forward (toward faders) to gain access to the
Fusion Console overbridge board.
2. Connect one end of the supplied Fusion power cable to the power port on the Fusion Console
overbridge board (B). Connect the other end to the 48DVC Output port (C) on the rear of the Axia
Power Supply. Connect the Axia Power Supply to AC Mains using the Axia Power Supply power
cable provided.
3. Connect Ethernet cable to the network connection port on the Fusion Console overbridge
board (D), connect other end to a configured Ethernet switch (E).
4. Connect Ethernet cable to the Livewire port (F) on the StudioEngine, connect other end to a
configured Ethernet switch (E).
5. Connect a 1080p monitor to the DVI-D video port (G) on the StudioEngine.
6. Close the Fusion Console overbridge panel (A).
7. Continue to Network Configuration with Axia StudioEngine.
PHysiCAl ConneCtions witH AxiA studioenGine
©2015 TLS Corp., All Rights Reserved.
C15/16009
