manualshive.com logo in svg

Award ECX800, User Manual

Share
Download
Award ECX800 User Manual Download Page 37

BIOS SETUP 

                              ECX800 User’s Manual 

33 

 
 
 
 
 
 
 
 
 
 
 

Integrated Peripherals 

This section sets configurations for your hard disk and other integrated 
peripherals. The first screen shows three main items for user to select. 
Once an item selected, a submenu appears. Details follow. 
 

Phoenix - AwardBIOS CMOS Setup Utility  

Integrated Peripherals 

OnChip IDE Device 

Press Enter 

ITEM HELP 

Onboard Device 

Press Enter 

Menu Level  > 

SuperIO Device 

Press Enter 

 

 

 

 

 

Phoenix - AwardBIOS CMOS Setup Utility  

OnChip IDE Device 

IDE HDD Block Mode 

Enabled ITEM 

HELP 

On-chip Primary PCI IDE 

Enabled  

IDE Primary Master PIO 

Auto 

IDE Primary Slave   PIO 

Auto 

IDE Primary Master UDMA 

Auto 

IDE Primary Slave   UDMA 

Auto 

On-Chip Secondary PCI IDE 

Enabled 

IDE Secondary Master PIO 

Auto 

IDE Secondary Slave   PIO 

Auto 

IDE Secondary Master UDMA 

Auto 

IDE Secondary Slave   UDMA 

Auto 

 

 

*** On-Chip Serial ATA Setting *** 

 

On-Chip Serial ATA 
SATA PORT Speed Settings 

Auto 
Disabled 

PATA IDE Mode 

Primary 

SATA port 

P1, P3 is Secondary 

 

 

Menu Level  > 

 

Phoenix - AwardBIOS CMOS Setup Utility  

Onboard Device 

USB Controller 

Enabled ITEM 

HELP 

USB 2.0 Controller 

Enabled 

USB Keyboard Support 

Disabled 

Azalia/AC97 Audio Select 

Auto 

 

 

Menu Level  > 

 

Summary of Contents for ECX800































































Reviews:

No comments

Brands by name

Popular brands

Load more brands