background image

33

Introduction

The AC-EX70-UHD-ARC consists of a transmitter and receiver that connect via single 

CAT-6a/7 UTP/STP. Connecting an HDMI signal to the transmitter allows for sending 

HDMI signals up to 70 meters at 1080p and up to 40 meters at 4K60 4:2:0, 4K30 

4:4:4.  This AVPro Edge audio video extender is the most cost-effective, state of the 

art, and reliable single CAT 70-meter extender on the market today.  It solves com-

mercial and residential market problems for distributing high-value 4K UHD content 

from rack to display with the additional ability to send an audio signal bi-directionally 

through HDMI’s Audio Return Channel (ARC). 

Features

 

·

HDMI 2.0

 

·

4K60 4:2:0, 4K30 4:4:4

 

·

HDR Support up to 4:2:2 12 Bit

 

·

Ultra Slim (.46 inch/11.7 mm)

 

·

Supports 3D

 

·

HDCP 2.2 & Earlier

 

·

CEC Pass Through

 

·

Supports ARC (Audio Return Channel)

 

·

70M (230ft) on 1080P (Cat6a)

 

·

Up to 40m (131ft) on 4K (Cat6a)

 

·

48v PoH (Power Over HDBaseT, only one Power 

Supply Needed)

 

·

I-Pass Feature for control system “pass-through”

 

·

3-20v protection circuit built in for safe IR trans-

port

 

·

Bi Directional RS232 Transport

 

·

LED Status, Link, Power indication lights

 

·

Use single UTP/STP LAN cable (CAT-6A) with 

substitute HDMI cable to achieve long distance 

transmission.

 

·

Supports uncompressed PCM 2- Ch., LPCM 5.1 

& 7.1, Dolby Digital, DTS, Dolby TrueHD, DTS 

HD-Master Audio, Atmos on HDMI

 

·

ESD protection circuitry (Inputs & Outputs) to 7KV

 

·

Can Cascade

In The Box

 

·

AC-EX70-UHD-TX (Transmitter)

 

·

AC-EX70-UHD-RX (Receiver)

 

·

1x 48V Power Supply (Can be pow-
ered at the Rx or Tx)

 

·

1 x IR Tx Unit

 

·

1 x IR Rx Unit

 

·

2 x Mini-Toslink adapters

 

·

3 Pin Terminal Connectors (For RS-
232 Control)

 

·

Rack Ears

Summary of Contents for AC-EX70-UHD-ARC




















Reviews: