manualshive.com logo in svg

AVK 41 Series, Field Maintenance And Instruction Manual

Share
Download
AVK 41 Series Field Maintenance And Instruction Manual Download Page 8

416

414

420

415

419

page 7

INSTALLATION - continued: 

SWING

 

 

A valve without a lever is referred to as ‘Swing’.  For Swing installation, follow the "INSTALLATION" instructions on page 3 .

  

LEVER AND WEIGHT (OPTIONAL)

 

Once the valve is properly installed, the lever and weight assembly needs to be attached to the Shaft (408) passing 

through the Open Bushing (417) in the Bonnet (407).  Slide the Lever (416) onto the Shaft (408) and position as shown in 

figure 4. Secure the Lever with the Shaft Washer (415) and Shaft Nut (414) and tighten to 30 ft-lbs.  Attach the Weight (419) 

and tighten the Set Screw (420) to hold the weight in place. A medium strength thread locking compound such as Locktite 242 

should be used to attach the Lever and Weight.

WARNING:

 

The weight can be moved on the lever to adjust closing speeds for optimum performance.  DO not adjust   

 

 

the weight while the system is operation.  Serious injury can occur.  

Fig. 5

Lever & Weight Mounting

Direction of Flow

Summary of Contents for 41 Series



















Reviews:

No comments

Brands by name

Popular brands

Load more brands