Avital AviStart 3100 Installation Manual Download

Page: 32 / 39

operating settings learn routine

The System Features Learn Routine dictates how the unit operates. The programmable operating settings of this

unit can be changed whenever necessary through the computer-based Learn Routine. The Program push-button

switch, plugged into the blue port, is used together with a programmed transmitter to change the settings. It is

possible to access and change any of the feature settings using the Program switch. To program settings, remem-

ber: Key, Choose, Transmit and Release.

To program the learn routine:

Key.

Turn the ignition on and then back off.

Choose.

Within 10 seconds, press and release the Program switch the number of times cor-

responding to the feature number you want to program. (See

Features Menu

section.)

Once the Program switch has been pressed and released the desired number of times, press it once more and

HOLD

it. After a second, the LED will flash to indicate which feature you have accessed. For example, groups of eight

flashes would indicate access to the status output feature (Feature 8).

Transmit.

The transmitter is used to select the desired setting. As shipped, the unit is con-

figured to the LED ON settings. These are called the default settings. Pressing Channel One

(usually Button I) will set it to the LED ON setting. The LED will light solid (stop flashing)

to indicate the setting. Pressing Channel 2 (usually Button II) will change the setting to

the LED OFF setting. The LED will go out indicating the change.

Release.

The Program switch can now be released.

You can advance from feature to feature by pressing and releasing the Program switch the number of times nec-

essary to get from the feature you just programmed to the feature you wish to access. For example, if you just

programmed the run time (Feature 3) and you next want to program parking lights (Feature 4) to constant, release

the Program switch. Press and release it once to advance from Feature 3 to Feature 4. Then press it once more

and

HOLD

it. The LED will flash in groups of 4 to confirm that you have accessed Feature 4.

The learn routine will be exited if any of the following occurs:

■

The ignition is turned on.

■

The Program switch is pressed too many times.

■

More than 25 seconds elapses between programming steps.

Summary of Contents for AviStart 3100








































Search results

Summary of Contents for AviStart 3100

Reviews:

Related manuals for AviStart 3100

Brands by name

Popular brands

Avital AviStart 3100, Installation Manual

Search results

Summary of Contents for AviStart 3100

Reviews:

Related manuals for AviStart 3100

Brands by name

Popular brands