G - REPLACING THE BATTERIES
The keypad will emit alerts when the batteries are low. Normally, the
keypad beeps when a key is pressed. When a key is pressed, the keypad
emits:
2 Beeps = Low battery warning. The keypad continues to transmit radio.
3 Beeps = Batteries very low. The keypad continues to transmit radio, but
the keypad will soon stop working.
1
2
3
4
5
6
7
8
9
A
0
B
H - RESETTING THE KEYPAD
Resetting the keypad will reset the MASTER code to the default setting
(999999), and delete all stored access codes.
To perform the reset, remove one battery from the keypad. Press and
hold the A button, and simultaneously replace the battery. Release the A
key after the keypad has emitted a series of 10 beeps.
Your keypad has now returned to its factory condition. (See chapter C
for programming)
Note: After resetting the keypad, it remains inactive for five seconds. If
you press a key during this time, it is normal for nothing to happen.
I - FAQ
DEFAULT
SOLUTION
The keypad does
not control the
motor drive
Ensure that the keypad is correctly programmed
on the motor drive's electronic card.
Verify that the keypad is within radio range of the
motor drive.
No beep when
key is pressed
Check that the batteries are inserted.
Check that the polarity of the batteries is correct.
When using the device for the first time, remove
the plastic cap from the battery connector.
Multiple beeps
per key press
Change the keypad's batteries.
J - TECHNICAL AND LEGAL INFORMA-
TION
J1 - TECHNICAL FEATURES:
• 10 easy-to-remember codes
• 4-digit access codes
• 6-digit master code
• Power supply: 2 LR03 AAA batteries
• Operating temperature: -20°C/+55°C
• Protection rating: IP44
• Radio frequency: 433 Mhz
• Radio range*: 80m in open air
• Dimensions: 73 x 86 x 30 mm
*The indicated radio range refers to the open air range, i.e. no obstacles
between the receiver and the transmitter. Any obstacle or disturbance will
reduce this range.
J2 - WARRANTY:
This product is guaranteed for parts and labour for 2 years from the date
of purchase. Proof of purchase must be retained for the duration of the
warranty period. The warranty does not cover damage caused by knocks
or accidents. This product must not be opened or repaired by any persons
not employed by AVIDSEN except to insert or replace the batteries.
So-called consumables, such as the batteries, are not covered by the
warranty.
J3 - ASSISTANCE AND ADVICE
• If, despite the care we have taken in designing our products and drafting
these instructions, you do encounter difficulties when installing your
product or you have any questions, we urge you to contact one of our
specialists who will be glad to help.
Technical assistance:
0,35 € / min
0 892 701 369
From Monday to Friday, 9am to 12pm and 2pm to 6pm.
• If you encounter operating problems during the installation or a few
days afterwards, it is highly recommended that you be in front of your
installation when contacting us, so that one of our technicians can
diagnose the source of the problem, as it will most likely be the result
of a setting that is incorrect or an installation that is not to specification.
If the problem is caused by the product itself, the technician will give you
an RMA number so that you can return the unit to the shop. Without this
RMA number, the shop may refuse to exchange the product.
• AVIDSEN undertakes to keep a stock of spare parts for this product
throughout the contractual warranty period.
J4 - DECLARATION OF COMPLIANCE
with the RED directive
AVIDSEN hereby declares that the undermentioned equipment: 114255
wireless keypad complies with the RED 2014/53/EU directive and that
its conformity has been assessed pursuant to the applicable standards
in force:
• EN 62368-1:2014 + A11:2017
• ETSI EN 301 489-1 V2.2.3:2019
• ETSI EN 301 489-3 V2.1.1:2019
• ETSI EN 300 220-1 V3.1.1:2017
• ETSI EN 300 220-2 V3.2.1:2018
• EN 62479:2010
Thus done in Tours 22/12/2020
Alexandre Chaverot,
CEO
