background image

www.avenview.com 

 

   

 

 

4X4 HDMI 1.3 over CAT5       
Matrix Switch with IR Pass-Through 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                   

 

 

 

 

 

© 2009 Avenview Inc. All rights reserved

.   

The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with 
respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any 
time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in 
Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products 
including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. 
Reproduction of this manual, or parts thereof,

 

in any form, without the express written permission of Avenview Inc. is strictly prohibited.                                                                                                                                                                                                                                                                                                                                 

 

Summary of Contents for 8X8 HDMI 1.3 over CAT5Matrix Switch with IR Pass-Through






















Reviews: