manualshive.com logo in svg

Aventics Marex ECS, Assembly Instructions Manual, Page: 38 / 60

Share
Download
Aventics Marex ECS Assembly Instructions Manual Download Page 38

Commissioning

AVENTICS

 | ECS Actuator | R417002911–BDL–001–AA

37

En

g

li

s

h

8.4

Connecting the push/pull cable

After all electric connections have been established and the 
actuators are operational, set up the mechanical connection 
between the MarexECS Actuator and the lever for speed or gear 
setting at the boat’s engine using a push/pull cable. 

Only use push/pull cables type 33C as the fixing points on 
the MarexECS Actuator are designed for that type of cable. 
Please note the push/pull cables are not included in the 
delivery, see also chapter 14, Accessories.

Proceed as follows:

1.

Select the lever at the throttle or gearbox which shall be 
connected first.

2.

Check if it is already prepared for the connection of a push/
pull cable. If not, a mounting kit is available including ball 
joint and mounting material (3236990062).

Connect the push/pull cable following the instructions of the 
manufacturer:

3.

Mount the ball of the joint onto the lever in such a way that 
the linear lever travel does not exceed 76mm. We 
recommend a lever travel of 70mm approximately (fig. 17).

Fig. 17: Adjusting lever and counter bearing

Summary of Contents for Marex ECS





























































Reviews:

No comments