manualshive.com logo in svg

Avaya Virtual Services Platform 7200 Series, Installation Manual

Share
Download
Avaya Virtual Services Platform 7200 Series Installation Manual Download Page 15

3. Remove the fan tray that failed by pushing the tab on the spring latch to the left and pulling

on the fan’s extraction handle.

4. Insert the new fan tray into the chassis.

Important:

You can hot swap fan trays while the switch is operational.

5. Verify that the fan tray is fully seated in the chassis. The spring latch should engage and

return to its original position.

6. Enter the following command to check the temperature sensors inside the switch.

show sys-info temperature

Example

Check the status of the fan trays.

VSP-7254XSQ:1>show sys-info fan

Fan Info : 

Fan Id     Fan Status      Fan Type

---------------------------------------

1          up              regularSpeed

2          up              regularSpeed

3          up              regularSpeed

  

Check the internal temperature of the switch.

VSP-7254XSQ:1>show sys-info temperature

Temperature Info : 

    CPU Temperature    MAC Temperature   PHY1 Temperature   PHY2 Temperature

         26                 29                 24                 27

January 2015

Installation Job Aid for Avaya Virtual Services Platform 7200 Series     

15

Summary of Contents for Virtual Services Platform 7200 Series


































Reviews:

No comments

Brands by name

Popular brands

Load more brands