Avaya S8300 Series Manual Download Page 45 | Manualshive

Page: 45 / 72

background image

Issue 2 June 2005

45

Chapter 5: Converting an S8300 from ICC to LSP

(Communication Manager 2.1 or later)

This chapter provides a high-level list of tasks for converting an S8300B primary controller to
LSP mode without performing an upgrade. To complete these tasks, you will need the following
additional documents:

●

Installation and Upgrades for Avaya G700 Media Gateway and Avaya S8300 Media
Server, 555-234-100. To obtain this document, go to

http://support.avaya.com

and

navigate to Installations, Migrations, Upgrades & Configurations; then select the
appropriate document.

●

Administrator Guide for Avaya Communication Manager, 03-300509.

●

Converting between an ICC and LSP

, which is for U.S.-based systems only. Similar

documents for non-US systems should be available from the regional web sites.

In this scenario, an S8300B, configured as an ICC, is converted to an S8300B in LSP mode. In
both modes, the media server is running Communication Manager release 2.1 or later and no
software/firmware upgrade is performed.

The tasks include:

1. Administering the primary controller for the new LSP.

2. Moving the endpoints supported by the ICC to the new primary controller.

3. Updating the DHCP server alternate controller list.

4. Updating the gateway MGC list.

5. Configuring the S8300B as an LSP.

Follow the detailed procedures in Installation and Upgrades for Avaya G700 Media Gateway
and Avaya S8300 Media Server, 555-234-100, Issue 8, April 2005, for most of the tasks in this
conversion scenario.

«
...
43
44
45
46
47
...
»

Summary of Contents for S8300 Series









































































Reviews:

No comments

Related manuals for S8300 Series

GW1102-2DRS-485-TB-P

Brand: 3onedata Pages: 3

Brand: Delta Pages: 2

Brand: Badger Meter Pages: 24

Brand: Valcom Pages: 4

Brand: HMS Pages: 26

Brand: MikroTik Pages: 22

Brand: NetComm Pages: 7

Brand: NetComm Pages: 4

NetComm Gateway Series

Brand: NetComm Pages: 62

Brand: NetComm Pages: 12

Selenio VMG-14+

Brand: Imagine communications Pages: 92

Brand: Zoom Pages: 48

Brand: Zoom Pages: 72

Brand: VOPtel Pages: 38

Firebox X Series

Brand: Watchguard Pages: 37

Brand: ZyXEL Communications Pages: 35

MediaAccess TG789vn

Brand: Technicolor Pages: 128

Brand: SmartRG Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands