manualshive.com logo in svg

Avaya P332MF, User Manual, Page: 150 / 182

Share
Download
Avaya P332MF User Manual Download Page 150

Chapter 6

CLI – Layer 2

134

Avaya P332MF User’s Guide

set radius authentication retry-time

Use the

 set radius authentication retry-time 

command to set the time 

to wait before re-sending an access request.

The syntax for this command is:

set radius authentication retry time <time>

set radius authentication retry-number

Use the

 set radius authentication retry-number 

command to set the 

number of times an access request is sent when there is no response.

The syntax for this command is:

set radius authentication retry number <number>

set radius authentication udp-port

Use the

 set radius authentication udp-port 

command to set the RFC 

2138 approved UDP port number. Normally, the UDP port number should be set to 
its default value of 1812. Some early implementations of the RADIUS server used 
port number 1645.

The syntax for this command is:

set radius authentication server udp-port <number>

time

Retry time in seconds

number

Retry number

Summary of Contents for P332MF























































































































































































Reviews:

No comments