Avaya J100 Series Installing And Administering Download Page 45 | Manualshive

Page: 45 / 528

Avaya J100 Series Installing And Administering Download Page 45

Parameter name

Default Value

Description

XSI_URL

Null

Specifies BroadWorks Xtended
Service Platform (XSP) server
FQDN/IP address, HTTP or
HTTPS mode and port. If the port
is not defined, 80 is used for
HTTP and 443 for HTTPS by
default.

This is the main parameter to
make features work in BroadSoft
environment.

Note:

If XSI_URL is defined, some local
call features will not be available.
They must be enabled for the
user on the BroadSoft server. For
more information, see

3CX configuration

3CX

3CX is one of the operation modes in open SIP environment. You can deploy Avaya J100 Series
IP Phones in the 3CX operation mode. For more information about 3CX , see

. For deploying the Avaya J100 Series IP Phones in 3CX mode, see

on page 45.

Related links

Open SIP operation modes

3CX PnP Provisioning

In

(Address allocation for private Internets) compliant local networks, if the 3CX server

and the phones are in the same subnet, the phones can auto-discover the provisioning server by
using 3CX Plug-and-play (PnP) provisioning. PnP provisioning uses IPv4 multicast address
(224.0.1.75), from IANA reserved addresses in the Internetwork Control Block (224.0.1.255) [

].

If the phone does not receive a provisioning server address from DHCP, LLDP, or DES, the phone
initiates PnP-based auto-discovery. The phone sends a SUBSCRIBE request to the special

3CX configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

45

Comments on this document? [email protected]

«
...
43
44
45
46
47
...
»

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments