Avaya G700 Installing And Upgrading Download Page 570

Page: 570 / 808

Manual upgrade of an S8300A and G700 to R4.0

570 Installing and Upgrading the Avaya G700 Media Gateway and Avaya S8300 Media Server

Installing the pre-upgrade service pack

Use

one

of the following two procedures to install the pre-upgrade service pack:

Current release is 1.x, use

To install the pre-upgrade service pack when the current release is

pre-2.0.

on page 570.

Current release is 2.x, use

To install the pre-upgrade service pack when the current release is

2.x.

on page 571.

To install the pre-upgrade service pack when the current release is pre-2.0.

1. Use Telnet to access the media server.

a. Click

Start > Run

to open the Run dialog box.

b. Type

telnet 192.11.13.6

and press

Enter

c. Log in as

craft

2. Type

cd /var/home/ftp

and press

Enter

to access the ftp directory.

3. At the prompt, type

ls -ltr

and press

Enter

to list files in the ftp directory.

The S8300 displays a list of files in the ftp directory.

4. Verify that the directory contains the

*.tar.gz

file you have uploaded.

5. Type

sudo patch_install

patch.

tar.gz

and press

Enter

where

patch

is the release or issue number of the service pack file. (For example,

03.1.526.5-1003.tar.gz

6. Type

patch_show

and press

Enter

to list Communication Manager files to verify the new

software file was installed.

7. Type

sudo patch_apply

patch

and press

Enter

where

patch

is the release or issue number of the service pack file. (For example,

03.1.526.5-1003

. Do

not

use the

*.tar.gz

extension at the end of the file name).

The media server goes through a software

reset system 4

. You must wait until the

restart/reset has completed before entering additional commands. The reset should take
1–2 minutes (or longer if messaging is enabled).

8. Type

patch_show

again and press

Enter

to list Communication Manager files to verify the

new software file was applied.

9. Before proceeding, type

statapp -c

to view the status of the processes.

Make sure everything except

dupmgr

shows

Communication Manager

should show

65/65 UP

or, if IA770 is installed,

67/67 UP.

To stop the continual refresh of the

statapp

command, type

Ctrl-C

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for G700

Reviews:

Avaya G700, Installing And Upgrading, Page: 570 / 808

Search results

Summary of Contents for G700

Reviews: