manualshive.com logo in svg

Avaya G700, Installing And Upgrading, Page: 41 / 808

Share
Download
Avaya G700 Installing And Upgrading Download Page 41

About connection and login methods

Issue 10.2 May 2007

41

 

About connection and login methods

This section describes the various ways of connecting to, and logging into, the Avaya™ S8300 
Media Server and the Avaya™ G700 Media Gateway. Use this chapter as a reference for the 
other chapters in this book.

The procedures in this book assume that you are connecting to the S8300 and/or the G700 with 
an Avaya Services laptop. However, the methods apply for any type of PC.

This chapter is organized as follows:

●

What physical access methods are available

●

Laptop configuration for direct connection to the services port

●

About connection methods

●

About Log in Methods

●

About navigation for G700 CLI commands

What physical access methods are available

Figure 1

 reviews physical access methods for the S8300 and G700. Check for the locations of 

the following ports:

●

If the S8300 is present in the G700,

- Services port in the center of the S8300

- USB ports on the right side of the S8300

●

If the S8300 is not present in the G700,

- Ethernet ports (EXT 1/ EXT 2) in the bottom center of the G700

You will need to connect the G700 to the customer’s LAN using one of these ports for 
loading the latest software.

- Console port at the lower right of the G700

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments