manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

Configuring IPv6 ICMP

Configure Internet Control Message Protocol (ICMP) to transport error and information

messages within IPv6 packets.

To view a list of ICMP messages, see 

ICMPv6 type and code

 on page 415.

Procedure steps

Configure the ICMP rate by using the following command:

config ipv6 icmp-error-interval

 

<0 through 2147483647>

Configuring neighbor discovery prefixes

IPv6 nodes on the same link use ND to discover link-layer addresses and to obtain and

advertise various network parameters and reachability information. ND combines the services

provided by Address Resolution Protocol (ARP) and router discovery for IPv4. IPv6 router

advertisement includes discovery prefixes.

Procedure steps

1. Configure discovery prefixes for a brouter port by using the following command:

config ethernet

 

<slot/port>

 

ipv6 nd-prefix <prefix/prefix length>

create

2. Configure discovery prefixes for a VLAN by using the following command:

config vlan

 

<vlan id>

 

ipv6 nd-prefix

 

<prefix/prefix length>

 

create

Variable definitions

Use the data in the following table to use the 

config ethernet ipv6 nd-prefix create

and 

config vlan ipv6 nd-prefix create

 commands.

Configuring IPv6 ICMP

Configuration — IPv6 Routing

November 2010     105

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

D-Linke DHP-346AV Quick Installation Manual preview
DHP-346AV
Brand: D-Linke Pages: 32
NEC N8104-213 Instructions Manual preview
N8104-213
Brand: NEC Pages: 8
Keithley 7707 User Manual preview
7707
Brand: Keithley Pages: 59
iDirect iQ Desktop+ Installation, Support, And Maintenance Manual preview
iQ Desktop+
Brand: iDirect Pages: 52
Surveon EonServ 5000 Series User Manual preview
EonServ 5000 Series
Brand: Surveon Pages: 33
National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Brand: National Instruments Pages: 36
IBASE Technology FWA8207 Series User Manual preview
FWA8207 Series
Brand: IBASE Technology Pages: 39
Mellanox Technologies ConnectX-3 Pro MCX349A-XCCN User Manual preview
ConnectX-3 Pro MCX349A-XCCN
Brand: Mellanox Technologies Pages: 35
Ubiquiti EdgeRouter ER-8 Quick Start Manual preview
EdgeRouter ER-8
Brand: Ubiquiti Pages: 20
Jensen of Scandinavia Air:Link 29150 Installation Manual preview
Air:Link 29150
Brand: Jensen of Scandinavia Pages: 2
METREL A 1475 Instruction Manual preview
A 1475
Brand: METREL Pages: 21
Axtrinet APG200 User Manual preview
APG200
Brand: Axtrinet Pages: 49
Planet IEEE 802.3at User Manual preview
IEEE 802.3at
Brand: Planet Pages: 2
Tripp Lite N302-18M Specification Sheet preview
N302-18M
Brand: Tripp Lite Pages: 2
D-Link DI-804V Owner'S Manual preview
DI-804V
Brand: D-Link Pages: 52
D-Link DES-1252 - Web Smart Switch Quick Installation Manual preview
DES-1252 - Web Smart Switch
Brand: D-Link Pages: 11
D-Link DES-1228 - Web Smart Switch Specifications preview
DES-1228 - Web Smart Switch
Brand: D-Link Pages: 4
D-Link DHP-347AV Quick Installation Manual preview
DHP-347AV
Brand: D-Link Pages: 32

Brands by name

Popular brands

Load more brands