Avaya DEFINITY Server R Manual Download Page 237

Page: 237 / 550

Remove Module Control Carrier(s)

Issue 7 November 2003

5-47

555-233-115

3. Disconnect the 16 ground straps from the top and bottom of the “A” carrier.

See

Figure 5-6

. These straps reconnect to the new “A” carrier.

Figure 5-6.

Locations of Ground Jumpers

Figure Notes

1. Rear of Cabinet

2. Port Carrier (“C” Position)

3. Ground Jumpers

4. Module Control Carrier (“A” Position)

5. Port Carrier (“D” Position)

Summary of Contents for DEFINITY Server R







































































































































































































































































































































































































































































































































































Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands

Avaya DEFINITY Server R, Manual

Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands