manualshive.com logo in svg

Avaya BSGX4e, Installation Manual

Share
Download
Avaya BSGX4e Installation Manual Download Page 17

17

BSGX4e Business Gateway Installation Guide

NN47928-303

Release 01.01

The following cables are required to install the BSGX4e:

For the signal pinouts of the BSGX4e connectors, see 

Signal Pins (page 43)

. 

Getting network information

The BSGX4e is inserted into the network between the router that provides access to 
the WAN and the devices on the LAN, including all analog and Voice over Internet 
Protocol (VoIP) phones. 

Figure 3

 shows an example layout of an IP network with the 

BSGX4e between the WAN and LAN. 

Figure 3. Network Connections

Serial cable To connect the CONSOLE port (DB9 connector) to a terminal (DB9 or 

Universal Serial Bus (USB) connector, depending on the terminal).

RJ45 to 
RJ45 cables

To connect the Ethernet ports to the WAN and to the LAN devices, 
CAT5E or better is recommended.

NOTE: The cables can be straight or crossover. The BSGX4e ports 

automatically determine if pairs need to be crossed over.

RJ11 to 
RJ11 cables

To connect the TELECOM ports. The LINE (FXO) port connects to the 
central office switch, and the PHONE (FXS) port connects to an analog 
device (such as a phone or fax machine).

Softswitch

TFTP 

Server

SNTP 

Server

Summary of Contents for BSGX4e

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands