Avaya AP100 Configuration Manual Download Page 4 | Manualshive

Page: 4 / 10

Avaya AP100 Configuration Manual Download Page 4

Meru Networks WLAN Controllers with AP100, AP201, AP208

Configuration Guide

Field Verified

Page 4

Multiple floor vertical layout, non-interfering channel coverage

Push-to-talk feature

Push-to-talk (PTT) is a handset communication mechanism supported by the wireless IP
telephone system. The mechanism uses multicast data delivery to communicate within the
wireless neighborhood. With guaranteed coverage across all access points, push-to-talk often
operates on a base rate as low as 1Mbps. Only a small set of handsets (3-4) can operate
within a PTT channel on the Meru Wireless system. A recommended method of improvement,
beyond multiple channel use for separation, is managing downlink data delivery at a higher
rate than uplink by removing the 1 and 2 Mbps basic rates (

no base-tx-rates 802.11bg 1

and

no

base-tx-rates 802.11bg 2

) for the ESS Profile. This provides some relief on channel space

usage and potentially increases the number of calls within the channel space.

«
...
2
3
4
5
6
...
»

Summary of Contents for AP100











Reviews:

No comments