manualshive.com logo in svg

Avaya 4524GT, Configuration Manual

Share
Download
Avaya 4524GT Configuration Manual Download Page 24

Figure 4: CFG mirror images in the stack after removing the BU (unit 1)

As shown in 

Figure 4: CFG mirror images in the stack after removing the BU (unit 1)

 on page 24

• Unit 2 becomes the TEMP-BU.

• The CFG 1 mirror image (residing in unit 2) becomes INACTIVE.

• A second copy of the INACTIVE CFG 1 mirror image is created in unit 3.

• The TEMP-BU (unit 2) contains all CFG mirror images of the NBUs in the stack.

• The CFG 2 mirror image is created in unit 3. Unit 3 becomes the next TEMP-BU in case

you remove the current TEMP-BU.

Restoring a CFG image

Restoring a CFG image overwrites the CFG image of a new unit in a stack with an INACTIVE
mirror image stored in the stack.

System configuration fundamentals

24     Configuration — System

April 2011

Summary of Contents for 4524GT











































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands