background image

SAFETY

ATTENTION: Important Safety Disclaimers

Read all instructions before using your adjustable base. Save these 

instructions

WARNING

Always unplug the base from electrical outlet before servicing any 

part of the base. Unplug the base before cleaning. To safely      

disconnect, ensure base is in a flat position with all motors off. 

TO REDUCE THE RISK OF SHOCK, FIRE OR INJURY: 

For optimal safety 

and operation, plug the bed base into a surge protector (not included). Ensure to 
always unplug the base from the electrical outlet before servicing or cleaning any 
part of the base. Keep the power cord away from heated surfaces. Discontinue 
use of the bed base and contact a qualified service centre if it has a damaged cord 
or plug, if it is not working properly, or it has been dropped into water. Only use 
this bed base for its intended use as described in this manual. Do not use accesso-
ries/ attachments that are not recommended by the manufacturer. 
Improper connection of the equipment can result in the risk of electrical shock, 
electrical fire or fault if the plug does not fit your outlet. Contact a qualified   
electrician to install a suitable outlet. 

PETS AND CHILDREN: 

Dispose of all packing materials immediately after 

opening as it may pose a risk to small children and pets. To avoid injury, it is not 
advised to allow children and small pets to play under the bed. Children should 
not operate the bed base without adult supervision. 

1.

Summary of Contents for LUXURYFLEX HI-LO

















Reviews: