background image

User Manual

www.AvantcoEquipment.com 3

Important Safeguards 

1. Thoroughly read this instruction manual prior to first use.

2.  Do not submerge unit and/or cord in water or any other liquids. Failure to heed this warning may result in electric 

shock, unit damage, and/or bodily injury.

3. Close supervision is suggested when unit is in use, especially when children are present.

4.  Check to ensure unit is in off position and unplugged when not in use or prior to cleaning. Allow grill to cool  

completely before cleaning.

5. Do not operate if the machine suffers serious damage or malfunctions. Contact dealer for repair or adjustment.

6.  It is recommended that you use only manufacturer issued parts and accessories with this unit. Using unapproved 

parts may result in damage or injury. This will also void the warranty.

7. Do not use outdoors.

8. Do not let cord hang over the edge of table or counter. Do not let it touch any hot surfaces.

9. Do not place appliance on or near gas or electric burners or heated ovens.

10. Securely insert plug into outlet. When unplugging, be sure to remove plug only. Never pull by the power cord.

Installation

1. To avoid equipment or electrical damage, make certain that the nameplate voltage is the same as the outlet voltage.

2. Electrical and grounding connections must be in compliance with the applicable portions of the electrical code.

3. Prior to first use, it is recommended that you clean the rollers of the machine with a soft cloth.

Operation Guide

1. Evenly place unfrozen hot dogs on the rollers.

2.  The left knob controls the front rollers and the right knob controls the back rollers. Both rows may be used for 

operation during high-volume use. 

3. Turn the roller switch on the control plate to “ON”. This switch controls the rotation of the rollers.

4.  Turn the knob to the desired heat level. After 40 minutes of heating the hot dogs, turn the temperature control knob 

on low to continuously keep warm.

5.  The heating duration depends on the hot dogs' quality. Please adjust as needed or required. Average heating 

duration is 40 minutes. This may vary.

Summary of Contents for 177RG1830RC









Reviews: