AVANT A36532 Operator'S Manual For Attachment Download Page 13

 

 

13 (26) 

 

 

 

 

DANGER - Risk of falling objects - Prevent 

dropping of attachment

 

An  attachment  that  has  not  been  completely 

locked  to  the  loader  may  fall  on  the  boom  or 

towards  the operator, or fall under  the loader 

during  driving,  causing  loss  of  control  of  the 

loader.  Never move or lift  an  attachment that 

has not been  locked.  Before  moving  or lifting 

the  attachment,  make  sure  that  the  locking 

pins  are  in  the  lower  position  and  come 

through  the  fasteners  on  the  attachment  on 

both sides. 

 

 

 

 
 

 

WARNING: Risk of crushing - Avoid tipping over the attachment.

 

Excessive tilting or lifting of an unlocked attachment increases the risk of tipping the 

attachment  over.  Do  not  use  the  automatic  locking  of  the  locking  pins  when  the 

attachment is lifted more than one meter from the ground. If the locking pins do not 

return  to  the  normal  position  when  tilting,  do  not  tilt  or  raise  the  attachment  any 

more. Lower the attachment on the ground and secure the locking manually. 

 

 

5.1

 

Connecting and disconnecting hydraulic hoses 

On Avant loaders the hydraulic hoses are connected using the multi connector system. If you have an Avant 
300-700 series loader with the conventional quick couplers and wish to change to the multi connector system, 
contact your Avant dealer or service point for instructions or installation services. 

 

 
 

 

WARNING: 

Never connect or disconnect quick couplings or other hydraulic components 

while the control lever of the auxiliary hydraulics control lever is locked on or if the system 

is  pressurized.  Connecting  or  disconnecting  the  hydraulic  couplings  while  the  system  is 

pressurized  may  lead  to  unintended  movements  of  the  attachment,  or  ejection  of 

high-pressure  fluid,  which  can  cause  serious  injuries  or  burns.  Follow  safe  stopping 

procedure before disconnecting hydraulics. 

 

 
 
 

 

Keep all fittings as clean as possible; use the protective caps on both the attachment and 
the  loader.  Dirt,  ice,  etc.  may  make  using  the  fittings  significantly  more  difficult.  Never 
leave  the  hoses  hanging  on  the  ground;  place  the  couplings  onto  the  holder  on  the 
attachment. 

 
 
 

Summary of Contents for A36532



























Reviews: