background image

POWER INPUT

GND

REM BATT+12V

SPEAKER OUTPUT

+

+

-

-

FUSE

6

Basic application

These sub bass amplifiers can be used in any of the bi-amplification systems described in
this manual, replacing the 2 channel amplifiers as per the illustrations.

Connect the inputs to a suitable source, e.g. a head unit with good quality RCA cables.
Connect the LINE OUT to the inputs of the system highs amplifier.

Use at least

#12 gauge speaker wiring. The amps have dual speaker terminals,

simplifying the hookup of multiple speakers. These amps are mono, 1 channel, amplifiers
which have multiple positive and negative connections for ease of wiring. The 2 positives
are the same internally and the 2 negatives are the same internally.

Refer to the section

Interconnect cable checklist:

Crossover frequency control checklist:
LOW PASS: 40Hz to 150Hz
SUBSONIC:15 Hz to 55 Hz
BASS EQ: 0 to +12dB

Level control checklist:

Minimum final loudspeaker impedance:
ATA1200.1 is capable 4 & 2-Ohms (not capable of 1-Ohm)
ATA2000.1 is capable of 4, 2 & 1-Ohm

“Setting up systems after installation for best performance”

FULL RANGE

STEREO LINE INPUT

NOT USED

Y-ADAPTOR

Note: You can use the Radio/CD designated mono line output or a full range stereo line output.
For full range stereo line output, you will need an optional “Y-Adaptor” as shown.

ATA 1200.1 / ATA2000.1 MONO AMPLIFIER APPLICATION

PARALLEL MONO

SUBWOOFERS

2-

OHMS EACH MINIMUM

DESIGNATED

MONO OUTPUT

FROM HEAD UNIT

OUTPUTINPUT

BASS

BOOST

SUB

SONIC

LOW

P

ASS

LEVEL

REMOTE

CONTROL

POWER

PROTECT

RR

L

L

0dB12dB15Hz55Hz40Hz150Hz6V0.2V

MIN MAXX

MONO

SUBWOOFER

POWERINPUT

GNDREMBA

TT+12V

SPEAKER+--

FUSE

REMOTE TURN-ON

CHASSIS GROUND

TO B12v

VIA FUSE

Summary of Contents for 2050.4














Reviews: