background image

AS PRG-1000 

AUTOSTART

 

TECH TOOL 

 

 

PRG-1000 Options

 

 

 

The remote starter can be programmed even when it is solely powered by the 
PRG-1000. 

 

The remote starter or alarm system must be disarmed or in Valet Mode to access 
the programmer’s menu. The PRG-1000 displays a “COMMUNICATION 
ERROR” message when trying to program an armed unit. 

 

Select one of the PRG-1000 functions (TACH/Hz, OBDII SCAN, REMOTE, 
DIAG., FUNCT, MODULE PROGRAMMING or INSTALLER 
PROGRAMMING FILES) to enter its menu. 

 

Use the “UP” and “DOWN” buttons to scroll the available options. 

 

Press “ENTER” to access the desired option. 

 

Repeat the above procedure if there are additional options you would like to 
access. 

 

Press “EXIT” to go back to the preceding option. 

 

Press “ENTER” followed by “WRITE” to save the new settings into the unit’s 
processor. New settings can be saved either one at the time or all at once, after all 
changes have been completed. 

 

Buttons & Functions 

1. ON/OFF BUTTON 

 

 
Press the “

ON/OFF

” button for 1 second to turn the PRG-1000 on. 

 

You will hear 3 beeps.  

 
To turn it off, press the “

ON/OFF

” button for 3 seconds.  

 

You will hear 2 beeps. 

 
The PRG-1000, if operating on its 9-volt battery, will turn off by itself if left unattended 
for more than 5 minutes. 
 
The programmer cannot be turned off, and will not automatically turn off, when it is 
powered through one of its link cables. As a reminder, 2 beeps will be heard every 5 
minutes if the programmer is left unattended. 

 

This tool is made for a 12-volt DC operation. To avoid damages, do not use it with 
other types (24-volt DC, 120 AC, etc.) of power sources. 

 

AS PRG-1000 

AUTOSTART

 

TECH TOOL 

 

 

14. Abbreviation Table of Functions and 

Options in Short Words 

 

No. Abbreviation 

Description 

1 ACC 

accessories 

2 AUX 

auxiliary 

3 Bsc 

basic 

operation 

4 Btn 

button 

5 CF 

car 

finder 

6 Conf 

 

confirmation 

7 Config 

configuration 

8 Const 

constant 

9 Cus 

customized 

operation 

10 

CWM 

cold weather mode 

11 Dis 

 

disarm 

12 

DomLite 

dome light supervision 

13 DZL 

diesel 

14 F 

function 

15 Gen 

generation 

16 Ide 

idle 

17 IGN 

ignition 

18 LK 

lock 

19 m 

minute(s) 

20 Mcr 

multi-car 

operation 

21 Mon 

monitoring 

22 ms 

millisecond(s) 

23 Notif 

notification 

24 Pass 

passive 

25 

PriorT 

priority door unlock 

26 RS 

remote 

start 

27 s 

second(s) 

28 SK 

starter 

kill 

29 SWS 

swap 

start 

30 Temp 

temperature 

31 Trk 

trunk 

32 Tub 

turbo 

33 ULK 

unlock 

34 V/S 

voltage 

sense 

35 W/ 

with 

36 W/O 

without 

 

Summary of Contents for AS PRG-1000









Reviews: